Red error LED flashing 10 times

Follow Avatar support@brightsign.biz

Last Updated: October 20, 2016

This indicates that a runtime error has occurred with the autorun.brs script. Script errors can be caused by a problem with the content or a bug in the autorun script. Follow these steps to troubleshoot the problem:

  1. Confirm that the Read-Only tab on the SD card is not in the locked position.
  2. If the player is running an older version of firmware, download and install the current production version from the Downloads page. You can determine the current firmware version by powering up the player without an SD card (or a different storage device) inserted: The version will be displayed on the screen.
  3. If you are using BrightAuthor:connected or BrightAuthor to publish presentations, download and install the current production version from the Downloads page.
  4. Verify that the SD/microSD card is formatted using FAT32 if you are using files smaller than 4GB. See this FAQ for more details.
  5. If you are using the older autoplay.bsp or autoplay.csv format, then an old autorun file or errors in the playlists can cause this kind of script error. 
Have more questions? Submit a request

24 Comments

Date Votes
  • 0
    Avatar
    Chris Butcher

    I have a XD232 that has just developed the 10x Error LED Fault, it has been running perfectly for over a year as our Demo unit that I take to clients offices and show the features.

    We always keep the firmware upto date and the last change to v6.0.51 was two weeks ago.

    I have followed the instructions above but every time I upload a Presentation that requires the BrightSign Network I get the 10x Error LED issue.

    So at the moment I am limited to only local Presentations.

    Any help would be appropriated with this issue as it has suddenly happened.

  • 0
    Avatar
    Chris Butcher
    Edited by Chris Butcher
  • 0
    Avatar
    Lyndon

    This happens with any presentaiton? Usually when you get 10 flashes, there's a line number reported where the crahs occurs. What line number are you failing on, and what version of the autorun.brs file do you currently have?

  • 0
    Avatar
    Chris Butcher

    Hi,

    I am not sure where I find the line number reported which crashed; Where do I find this information?

    After testing various presentations, it seems to be limited to one Presentation and it doesn't matter if I have the player setup in Local Network Mode or BrightSign Network Mode I get errors.

    For example if the Player is in Local mode I get the 10x Red LED and the unit keeps rebooting unless I disable the "autorun" via the builtin diagnostic section within the  web server.

    However if I use the same another unit is BrightSign Network mode I get emails coming back informing me that it is in an error state and they list "4/18/2016 2:51:27 PM UTC: Syntax Error. (runtime error &h02) in SD:/autorun.brs(28472); (Error code: 0)"

    I am using v7.4.16 Autorun with Firmware v6.0.51

    Edited by Chris Butcher
  • 0
    Avatar
    Chris Butcher

    Hi,

    I have noticed the same fault again.

    The system has been running fine for almost a week, I then updated the schedule via the BrightSign Network and on the next reboot the same fault happened.

    I have checked the error log via the BSN and it lists: 

    21 Apr 2016 05:07:18 UTC
    ScriptRuntimeError
    Message: Syntax Error. (runtime error &h02) in SD:/autorun.brs(28472);
     
    I have rebooted the unit and uploaded a new layout but the system still has the same issue.  The only way I resolved it last time was to leave it unplugged for an hour.  After that time it downloaded the layout and the schedule without an issue.
     
    Any ideas
  • 0
    Avatar
    Lyndon

    This is the line where the failure is occurring:

    if item.type = "text/html" or item.type = "application/widget" or item.medium = "document" then

     

    DO you have a project or combination of projects that can cause this problem more frequently? If so, I'd like to get those so I can duplicate on my end and then look at what exactly is causing the failure. A tthe moment, it seems like a bug in the autorun script that playsback your project.

    But I need access to a failing player to find out what on that line is invalid. 

  • 0
    Avatar
    Dan Phelps

    Was this issue ever resolved?

    I seem to be having the same issue on an XD232 as well.

    Error message below:

    10 Red LED flashes and eventually reboots and repeats the cycle.

    6/13/2016 3:01:16 AM UTC: STOP (runtime error &hf7) in SD2:/autorun.brs(28958); (Error code: 0)

     

    -Dan

  • 0
    Avatar
    Chris Butcher

    Hi Dan,

    The issues relates to a glitch in the firmware, specifically to do with 'Dynamic Playlists' on a BrightSign Network account.

    If you have a playlist that either has no images assigned or it contains images which are not scheduled to appear (All Paused or Stopped) then the Player gives the Red LED 10 times and then it reboots.

    To work around the glitch I have setup a Presentation which the client changes the images once a week to keep upto date with their Menu Board without scheduling any dates; if they don't need an image relating to the Menu item then they insert a 'Blank' image.

    I am still waiting for a new firmware to be released which fixes this issue as they client would like to schedule upto 9 weeks ahead which matches their Term Menu selections.

     

    Cheers. Chris

  • 0
    Avatar
    Kevin Gage

    I am having the same issue with the most current f/w and my XD1230 and using BSA 4.4.0.15.

    The player boots to the f/w (6.1.76) screen but 10x flash errors when trying to load from the SD card.

    How can I generate a log detailing the error?

     

    KG

  • 0
    Avatar
    Lyndon

     

    In the system log on the player, does it show the line that the unit crashed on? After boot, but before crash and reboot, go to http://playeripaddress/lastkmsg.html. 

     

    For example:

    http://10.1.1.109/lastkmsg.html

     

    From one of my players, it starts like this:

     

    lastring

    <5>[    0.000] Linux version 3.3.8-3.0+bs6.1.100 (jenkins@bob) (gcc version 4.9.3 (GCC) ) #1 PREEMPT Fri Sep 16 17:33:51 BST 2016
<6>[    0.000] Fetching vars from bootloader... found 29 vars.
<4>[    0.000] BrightSign board ID: 1
<6>[    0.000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm7425-gpio-lo
<6>[    0.000] gpiochip_add: registered GPIOs 32 to 63 on device: bcm7425-gpio-hi
<6>[    0.000] gpiochip_add: registered GPIOs 64 to 89 on device: bcm7425-gpio-ext

     

    and ends like this...

     

    The system is going down NOW!
<4>[  131.817] 
Sent SIGTERM to all processes
<4>[  131.819] ptp4l: caught signal 15
<4>[  131.896] wlan0: CTRL-EVENT-TERMINATING 
<4>[  132.820] 
Sent SIGKILL to all processes
<4>[  132.822] 
Unmounted /dev/shm
<4>[  132.823] 
Unmounted /sys
<4>[  132.824] 
Unmounted /var/volatile
<4>[  132.824] 
Unmounted /proc
<4>[  132.824] 
Unmounted /
<4>[  132.824] init: none busy - remounted read-only
<4>[  132.824] 
Unmounted /dev
<4>[  132.824] 
Unmounted /
<4>[  132.824] 
All filesystems are now unmounted
<4>[  132.824] 
Requesting system reboot
<0>[  133.828] Restarting system.
  • 0
    Avatar
    Kevin Gage

    BrightSign®
    INFO
    LOG
    CONTROL
    SD
    DIAGNOSTICS
    VIDEO
    lastring
    <5>[ 0.000] Linux version 3.3.8-3.0+bs6.1.76 (jenkins@bob) (gcc version 4.9.3 (GCC) ) #1 PREEMPT Fri May 13 15:40:31 BST 2016
    <6>[ 0.000] Fetching vars from bootloader... found 24 vars.
    <4>[ 0.000] BrightSign board ID: 8
    <6>[ 0.000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm7425-gpio-lo
    <6>[ 0.000] gpiochip_add: registered GPIOs 32 to 63 on device: bcm7425-gpio-hi
    <6>[ 0.000] gpiochip_add: registered GPIOs 64 to 89 on device: bcm7425-gpio-ext
    <6>[ 0.000] gpiochip_add: registered GPIOs 90 to 98 on device: bcm7425-gpio-ext-hi
    <6>[ 0.000] gpiochip_add: registered GPIOs 99 to 110 on device: bcm7425-gpio-ext-hi-output
    <6>[ 0.000] gpiochip_add: registered GPIOs 152 to 157 on device: bcm7425-sgpio
    <6>[ 0.000] gpiochip_add: registered GPIOs 160 to 177 on device: bcm7425-gpio-aon-lo
    <6>[ 0.000] gpiochip_add: registered GPIOs 178 to 181 on device: bcm7425-gpio-aon-ext
    <6>[ 0.000] Options: moca=0 sata=1 pcie=1 usb=1
    <6>[ 0.000] Using 512 MB + 512 MB RAM (from kernel configuration)
    <6>[ 0.000] CPU revision is: 00025a11 (Broadcom BMIPS5000)
    <6>[ 0.000] FPU revision is: 00130001
    <6>[ 0.000] Determined physical RAM map:
    <6>[ 0.000] memory: 10000000 @ 00000000 (usable)
    <6>[ 0.000] memory: 10000000 @ 20000000 (usable)
    <6>[ 0.000] memory: 07400000 @ 90000000 (usable)
    <4>[ 0.000] bmem: nothing specified on command line, adding default regions
    <7>[ 0.000] bmem: adding 54 MB LINUX region at 9 MB (0x0365b000@0x009a5000)
    <6>[ 0.000] bmem: adding 128 MB RESERVED region at 64 MB (0x08000000@0x04000000)
    <7>[ 0.000] bmem: adding 64 MB LINUX region at 192 MB (0x04000000@0x0c000000)
    <6>[ 0.000] bmem: adding 120 MB RESERVED region at 512 MB (0x07800000@0x20000000)
    <7>[ 0.000] bmem: adding 136 MB LINUX region at 632 MB (0x08800000@0x27800000)
    <6>[ 0.000] Initrd not found or empty - disabling initrd
    <4>[ 0.000] Zone PFN ranges:
    <4>[ 0.000] Normal 0x00000000 -> 0x00050000
    <4>[ 0.000] HighMem 0x00050000 -> 0x00097400
    <4>[ 0.000] Movable zone start PFN for each node
    <4>[ 0.000] Early memory PFN ranges
    <4>[ 0.000] 0: 0x00000000 -> 0x00010000
    <4>[ 0.000] 0: 0x00020000 -> 0x00030000
    <4>[ 0.000] 0: 0x00090000 -> 0x00097400
    <7>[ 0.000] On node 0 totalpages: 160768
    <7>[ 0.000] Normal zone: 2560 pages used for memmap
    <7>[ 0.000] Normal zone: 0 pages reserved
    <7>[ 0.000] Normal zone: 128512 pages, LIFO batch:31
    <7>[ 0.000] HighMem zone: 2280 pages used for memmap
    <7>[ 0.000] HighMem zone: 27416 pages, LIFO batch:7
    <7>[ 0.000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
    <7>[ 0.000] pcpu-alloc: [0] 0
    <4>[ 0.000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 155928
    <5>[ 0.000] Kernel command line:
    <6>[ 0.000] PID hash table entries: 2048 (order: 1, 8192 bytes)
    <6>[ 0.000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
    <6>[ 0.000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
    <4>[ 0.000] Primary instruction cache 32kB, physically tagged, 4-way, linesize 64 bytes.
    <4>[ 0.000] Primary data cache 32kB, 4-way, linesize 32 bytes.
    <4>[ 0.000] MIPS secondary cache 256kB, 8-way, linesize 128 bytes.
    <6>[ 0.000] Memory: 372616k/524288k available (5086k kernel code, 270456k reserved, 1217k data, 1900k init, 118784k highmem)
    <6>[ 0.000] SLUB: Genslabs=9, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    <6>[ 0.000] NR_IRQS:266
    <6>[ 0.000] Measuring MIPS counter frequency...
    <6>[ 0.000] Detected MIPS clock frequency: 1305 MHz (163.135 MHz counter)
    <6>[ 0.000] Calibrating delay loop... 869.37 BogoMIPS (lpj=434688)
    <6>[ 0.009] pid_max: default: 32768 minimum: 301
    <6>[ 0.009] Mount-cache hash table entries: 512
    <6>[ 0.009] Performance counters: BMIPS5000 PMU enabled, 4 32-bit counters available to each CPU, irq -1 (share with timer interrupt)
    <7>[ 0.009] bcm40nm_pm_moca_disable 00
    <6>[ 0.009] devtmpfs: initialized
    <4>[ 0.010] core_dumped: 0, 0
    <6>[ 0.010] bmem: adding extra 396 MB RESERVED region at 2420 MB (0x18c00000@0x97400000) (MEMC1)
    <6>[ 0.010] NET: Registered protocol family 16
    <6>[ 0.011] USB0: power enable is active high; overcurrent is active low
    <6>[ 0.011] USB1: power enable is active low; overcurrent is active low
    <7>[ 0.011] __clk_disable: pcie [0]
    <7>[ 0.011] bcm7425_pm_pcie_disable 00
    <6>[ 0.011] PCI: PCIe link down
    <6>[ 0.013] bio: create slab <bio-0> at 0
    <5>[ 0.014] SCSI subsystem initialized
    <6>[ 0.014] usbcore: registered new interface driver usbfs
    <6>[ 0.014] usbcore: registered new interface driver hub
    <6>[ 0.014] usbcore: registered new device driver usb
    <6>[ 0.014] Advanced Linux Sound Architecture Driver Version 1.0.24.
    <6>[ 0.014] PCI host bridge to bus 0000:00
    <6>[ 0.014] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
    <6>[ 0.014] pci_bus 0000:00: root bus resource [mem 0x00000400-0x000007ff]
    <6>[ 0.014] Bluetooth: Core ver 2.16
    <6>[ 0.015] NET: Registered protocol family 31
    <6>[ 0.015] Bluetooth: HCI device and connection manager initialized
    <6>[ 0.015] Bluetooth: HCI socket layer initialized
    <6>[ 0.015] Bluetooth: L2CAP socket layer initialized
    <6>[ 0.015] Bluetooth: SCO socket layer initialized
    <6>[ 0.015] Switching to clocksource wktmr
    <6>[ 0.015] NET: Registered protocol family 2
    <6>[ 0.015] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
    <6>[ 0.016] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
    <6>[ 0.016] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
    <6>[ 0.016] TCP: Hash tables configured (established 16384 bind 16384)
    <6>[ 0.016] TCP reno registered
    <6>[ 0.016] UDP hash table entries: 256 (order: 0, 4096 bytes)
    <6>[ 0.016] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
    <6>[ 0.016] NET: Registered protocol family 1
    <6>[ 0.020] gpiochip_add: registered GPIOs 196 to 203 on device: brightsign-gpio
    <6>[ 0.020] gpiochip_add: registered GPIOs 215 to 215 on device: brightsign-busy-led
    <6>[ 0.020] gpiochip_add: registered GPIOs 205 to 206 on device: brightsign-leds-1
    <6>[ 0.020] gpiochip_add: registered GPIOs 212 to 214 on device: brightsign-leds-2
    <6>[ 0.020] gpiochip_add: registered GPIOs 209 to 209 on device: brightsign-server-led
    <6>[ 0.020] gpiochip_add: registered GPIOs 207 to 208 on device: brightsign-reset-button
    <7>[ 0.021] Registered led device: ethernet
    <4>[ 0.067] highmem bounce pool size: 64 pages
    <6>[ 0.070] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    <6>[ 0.071] NTFS driver 2.1.30 [Flags: R/O].
    <6>[ 0.071] msgmni has been set to 495
    <6>[ 0.071] io scheduler noop registered
    <6>[ 0.071] io scheduler deadline registered (default)
    <6>[ 0.072] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    <6>[ 0.072] serial8250.0: ttyS0 at MMIO 0x10406b00 (irq = 62) is a 16550A
    <6>[ 0.072] serial8250.0: ttyS1 at MMIO 0x10406b40 (irq = 63) is a 16550A
    <6>[ 0.072] serial8250.0: ttyS2 at MMIO 0x10406b80 (irq = 64) is a 16550A
    <6>[ 0.074] loop: module loaded
    <6>[ 0.074] brcmstb_nand: NAND controller driver is loaded
    <6>[ 0.074] ubiblk: major device number is 254
    <7>[ 0.074] __clk_enable: network [1]
    <7>[ 0.074] bcm7425_pm_network_enable 00
    <7>[ 0.074] __clk_enable: enet [1]
    <7>[ 0.074] bcm40nm_pm_genet_enable 00
    <6>[ 0.176] bcmgenet: configuring instance #0 for internal PHY
    <6>[ 0.196] bcmgenet bcmgenet.0: eth0: link down
    <7>[ 0.196] __clk_disable: enet [0]
    <7>[ 0.196] bcm40nm_pm_genet_disable 00
    <7>[ 0.196] __clk_disable: network [0]
    <7>[ 0.196] bcm7425_pm_network_disable 00
    <6>[ 0.196] PPP generic driver version 2.4.2
    <6>[ 0.196] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    <7>[ 0.196] __clk_enable: usb [1]
    <7>[ 0.196] bcm40nm_pm_usb_enable 00
    <6>[ 0.196] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
    <6>[ 0.196] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
    <6>[ 0.227] ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
    <6>[ 0.233] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
    <6>[ 0.233] hub 1-0:1.0: USB hub found
    <6>[ 0.233] hub 1-0:1.0: 1 port detected
    <6>[ 0.233] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
    <6>[ 0.233] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
    <6>[ 0.264] ehci-brcm ehci-brcm.1: irq 67, io mem 0x10480500
    <6>[ 0.270] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
    <6>[ 0.270] hub 2-0:1.0: USB hub found
    <6>[ 0.270] hub 2-0:1.0: 1 port detected
    <6>[ 0.270] ehci-brcm ehci-brcm.2: Broadcom STB EHCI
    <6>[ 0.270] ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
    <6>[ 0.301] ehci-brcm ehci-brcm.2: irq 71, io mem 0x10490300
    <6>[ 0.307] ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
    <6>[ 0.307] hub 3-0:1.0: USB hub found
    <6>[ 0.307] hub 3-0:1.0: 1 port detected
    <6>[ 0.307] ehci-brcm ehci-brcm.3: Broadcom STB EHCI
    <6>[ 0.307] ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
    <6>[ 0.338] ehci-brcm ehci-brcm.3: irq 72, io mem 0x10490500
    <6>[ 0.344] ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
    <6>[ 0.344] hub 4-0:1.0: USB hub found
    <6>[ 0.344] hub 4-0:1.0: 1 port detected
    <6>[ 0.344] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    <6>[ 0.344] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
    <6>[ 0.344] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
    <6>[ 0.344] ohci-brcm ohci-brcm.0: irq 68, io mem 0x10480400
    <6>[ 0.409] hub 5-0:1.0: USB hub found
    <6>[ 0.409] hub 5-0:1.0: 1 port detected
    <6>[ 0.409] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
    <6>[ 0.409] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
    <6>[ 0.409] ohci-brcm ohci-brcm.1: irq 69, io mem 0x10480600
    <6>[ 0.474] hub 6-0:1.0: USB hub found
    <6>[ 0.474] hub 6-0:1.0: 1 port detected
    <6>[ 0.474] ohci-brcm ohci-brcm.2: Broadcom STB OHCI
    <6>[ 0.474] ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
    <6>[ 0.474] ohci-brcm ohci-brcm.2: irq 73, io mem 0x10490400
    <6>[ 0.539] hub 7-0:1.0: USB hub found
    <6>[ 0.539] hub 7-0:1.0: 1 port detected
    <6>[ 0.539] ohci-brcm ohci-brcm.3: Broadcom STB OHCI
    <6>[ 0.539] ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
    <6>[ 0.539] ohci-brcm ohci-brcm.3: irq 74, io mem 0x10490600
    <6>[ 0.604] hub 8-0:1.0: USB hub found
    <6>[ 0.604] hub 8-0:1.0: 1 port detected
    <6>[ 0.604] usbcore: registered new interface driver cdc_acm
    <6>[ 0.604] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
    <6>[ 0.604] usbcore: registered new interface driver usblp
    <6>[ 0.604] Initializing USB Mass Storage driver...
    <6>[ 0.604] usbcore: registered new interface driver usb-storage
    <6>[ 0.604] USB Mass Storage support registered.
    <6>[ 0.604] usbcore: registered new interface driver usbserial
    <6>[ 0.604] usbserial: USB Serial Driver core
    <6>[ 0.604] USB Serial support registered for ch341-uart
    <6>[ 0.604] usbcore: registered new interface driver ch341
    <6>[ 0.604] USB Serial support registered for cp210x
    <6>[ 0.605] usbcore: registered new interface driver cp210x
    <6>[ 0.605] cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
    <6>[ 0.605] USB Serial support registered for FTDI USB Serial Device
    <6>[ 0.605] usbcore: registered new interface driver ftdi_sio
    <6>[ 0.605] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
    <6>[ 0.605] USB Serial support registered for GSM modem (1-port)
    <6>[ 0.605] usbcore: registered new interface driver option
    <6>[ 0.605] option: v0.7.2:USB Driver for GSM modems
    <6>[ 0.605] USB Serial support registered for pl2303
    <6>[ 0.605] usbcore: registered new interface driver pl2303
    <6>[ 0.605] pl2303: Prolific PL2303 USB to serial adaptor driver
    <6>[ 0.605] USB Serial support registered for Sierra USB modem
    <6>[ 0.605] usbcore: registered new interface driver sierra
    <6>[ 0.605] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
    <6>[ 0.605] mousedev: PS/2 mouse device common for all mice
    <6>[ 0.606] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
    <3>[ 0.606] LED update led is currently 0
    <6>[ 0.606] elo_mt_input: loaded
    <6>[ 0.606] usbcore: registered new interface driver usbtouchscreen
    <6>[ 0.606] i2c /dev entries driver
    <6>[ 0.606] lirc_dev: IR Remote Control driver registered, major 253
    <6>[ 0.606] IR LIRC bridge handler initialized
    <6>[ 0.606] usbcore: registered new interface driver streamzap
    <6>[ 0.606] Linux video capture interface: v2.00
    <6>[ 0.606] usbcore: registered new interface driver btusb
    <6>[ 0.606] sdhci: Secure Digital Host Controller Interface driver
    <6>[ 0.606] sdhci: Copyright(c) Pierre Ossman
    <6>[ 0.606] sdhci-pltfm: SDHCI platform and OF driver helper
    <6>[ 0.606] sdhci-brcmstb sdhci-brcmstb.0: Enabling controller
    <6>[ 0.606] sdio0: Setting OP_DLY=0x80020007
    <6>[ 0.606] sdio0: Setting IP_DLY=0x8003000a
    <7>[ 0.608] Registered led device: mmc0::
    <6>[ 0.611] mmc0: SDHCI controller on sdhci-brcmstb.0 [sdhci-brcmstb.0] using ADMA
    <6>[ 0.611] sdhci-brcmstb sdhci-brcmstb.1: Enabling controller
    <6>[ 0.611] sdio1: Setting OP_DLY=0x80020007
    <6>[ 0.611] sdio1: Setting IP_DLY=0x80030009
    <6>[ 0.611] sdhci_brcmstb_probe: Registering Cheetah platform ops for EMMC controller
    <7>[ 0.613] Registered led device: mmc1::
    <6>[ 0.626] mmc1: SDHCI controller on sdhci-brcmstb.1 [sdhci-brcmstb.1] using ADMA
    <7>[ 0.626] Registered led device: busy
    <7>[ 0.626] Registered led device: wifi
    <7>[ 0.626] Registered led device: micro-sd
    <6>[ 0.626] usbcore: registered new interface driver usbhid
    <6>[ 0.626] usbhid: USB HID core driver
    <6>[ 0.626] usbcore: registered new interface driver snd-usb-audio
    <6>[ 0.626] ALSA device list:
    <6>[ 0.626] No soundcards found.
    <6>[ 0.626] u32 classifier
    <6>[ 0.626] Actions configured
    <6>[ 0.626] TCP cubic registered
    <6>[ 0.627] NET: Registered protocol family 10
    <6>[ 0.627] NET: Registered protocol family 17
    <6>[ 0.627] Bluetooth: RFCOMM TTY layer initialized
    <6>[ 0.627] Bluetooth: RFCOMM socket layer initialized
    <6>[ 0.627] Bluetooth: RFCOMM ver 1.11
    <6>[ 0.627] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    <6>[ 0.627] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    <6>[ 0.627] PM: CP0 COUNT/COMPARE frequency does not depend on divisor
    <6>[ 0.628] EBI CS0: setting up NAND flash (primary)
    <6>[ 0.628] ONFI param page 0 valid
    <6>[ 0.628] ONFI flash detected
    <6>[ 0.628] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix H27U2G8F2CTR-BC)
    <6>[ 0.629] ONFI param page 0 valid
    <6>[ 0.629] ONFI flash detected
    <6>[ 0.629] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix H27U2G8F2CTR-BC)
    <6>[ 0.629] brcmnand brcmnand.0: 256MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
    <6>[ 0.629] Bad block table found at page 131008, version 0x01
    <6>[ 0.629] Bad block table found at page 130944, version 0x01
    <5>[ 0.630] Creating 7 MTD partitions on "brcmnand.0":
    <5>[ 0.630] 0x000000000000-0x000000180000 : "cfe"
    <5>[ 0.630] 0x000000180000-0x000000200000 : "devid"
    <5>[ 0.630] 0x000000200000-0x000000240000 : "cfenvram"
    <5>[ 0.630] 0x000000240000-0x000000840000 : "rescue"
    <5>[ 0.630] 0x000000840000-0x000000c40000 : "kernel"
    <5>[ 0.631] 0x000000c40000-0x000010000000 : "ubi"
    <5>[ 0.631] 0x000000000000-0x000010000000 : "entire_device"
    <6>[ 0.631] i2c-gpio i2c-gpio.0: using pins 157 (SDA) and 156 (SCL)
    <6>[ 0.632] i2c-gpio i2c-gpio.1: using pins 155 (SDA) and 154 (SCL)
    <6>[ 0.703] xc5000 1-0061: creating new instance
    <6>[ 0.704] xc5000: Successfully identified at address 0x61
    <6>[ 0.704] xc5000: Firmware has not been loaded previously
    <6>[ 0.704] DVB: registering new adapter (bs_cheetah_platform)
    <4>[ 0.704] DVB: registering adapter 0 frontend 0 (LG Electronics LGDT3305 VSB/QAM Frontend)...
    <4>[ 0.704] Warning: unable to open an initial console.
    <6>[ 0.706] Freeing unused kernel memory: 1900k freed
    <6>[ 0.707] kmsg output is not also going to console.
    <4>[ 0.707] initramfs started...
    <5>[ 0.707] UBI: attaching mtd5 to ubi0
    <5>[ 0.707] UBI: physical eraseblock size: 131072 bytes (128 KiB)
    <5>[ 0.707] UBI: logical eraseblock size: 126976 bytes
    <5>[ 0.707] UBI: smallest flash I/O unit: 2048
    <5>[ 0.707] UBI: VID header offset: 2048 (aligned 2048)
    <5>[ 0.707] UBI: data offset: 4096
    <5>[ 2.150] UBI: max. sequence number: 5229
    <5>[ 2.161] UBI: attached mtd5 to ubi0
    <5>[ 2.161] UBI: MTD device name: "ubi"
    <5>[ 2.161] UBI: MTD device size: 243 MiB
    <5>[ 2.161] UBI: number of good PEBs: 1946
    <5>[ 2.161] UBI: number of bad PEBs: 4
    <5>[ 2.162] UBI: number of corrupted PEBs: 0
    <5>[ 2.162] UBI: max. allowed volumes: 128
    <5>[ 2.162] UBI: wear-leveling threshold: 4096
    <5>[ 2.162] UBI: number of internal volumes: 1
    <5>[ 2.162] UBI: number of user volumes: 2
    <5>[ 2.162] UBI: available PEBs: 1037
    <5>[ 2.162] UBI: total number of reserved PEBs: 909
    <5>[ 2.162] UBI: number of PEBs reserved for bad PEB handling: 19
    <5>[ 2.162] UBI: max/mean erase counter: 23/3
    <5>[ 2.162] UBI: image sequence number: -487293677
    <6>[ 2.162] misc ubiblk_ctrl: proxying ubi0:1
    <5>[ 2.162] UBI: background thread "ubi_bgt0d" started, PID 30
    <6>[ 2.162] block ubiblk0_1: created from ubi0:1(rootfs)
    <4>[ 2.162] Verifying rootfs...
    <4>[ 16.186] Mounting rootfs from /dev/ubiblk0_1
    <4>[ 16.420] mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
    <4>[ 16.429] UBI volume is 1946 blocks
    <5>[ 16.784] UBIFS: mounted UBI device 0, volume 0, name "writable"
    <5>[ 16.784] UBIFS: file system size: 15745024 bytes (15376 KiB, 15 MiB, 124 LEBs)
    <5>[ 16.784] UBIFS: journal size: 1015809 bytes (992 KiB, 0 MiB, 6 LEBs)
    <5>[ 16.784] UBIFS: media format: w4/r0 (latest is w4/r0)
    <5>[ 16.784] UBIFS: default compressor: lzo
    <5>[ 16.784] UBIFS: reserved for root: 743676 bytes (726 KiB)
    <4>[ 16.785] Using user-space nexus
    <4>[ 16.794] bcmdriver: module license 'Proprietary' taints kernel.
    <4>[ 16.794] Disabling lock debugging due to kernel taint
    <6>[ 16.794] BCMDRV: Initializing bcmdriver version $ 4
    <6>[ 16.794] BCMDRV: Total intc words=3,Total Irqs=97
    <6>[ 16.796] BCMDRV: Initialization complete
    <6>[ 16.934] BRIGHTSIGN boot=4.4.15 rescue=4.4.15 mission=6.1.76 model=XD1230 REVG serial=X2G3AF001367 hw=3916f7d sk=1 sb=1
    <4>[ 17.020] Starting system message bus:
    <4>[ 17.099] dbus.
    <3>[ 17.341] lttng-sessiond(84):close(3) returning EBADF
    <4>[ 17.475] Spawning a session daemon
    <4>[ 17.475] Session bs created.
    <4>[ 17.475] Traces will be written in /var/volatile/lttng/lttng-traces/bs-19700101-000017
    <4>[ 17.609] UST channel channel0 enabled for session bs
    <4>[ 17.654] UTC read from RTC: Wed Oct 26 19:18:40 2016
    <4>[ 17.656] Looking for crash dump:
    <4>[ 17.713] Reset causes: 0x100 reboot
    <4>[ 17.713] No post-mortem crash dump available.
    <4>[ 17.714] done.
    <4>[ 17.747] Starting dhcpcd eth0
    <4>[ 17.969] net-configure: eth0 start
    <4>[ 17.999] sys_close: 1020 callbacks suppressed
    <3>[ 17.999] net-configure(115):close(7) returning EBADF
    <4>[ 18.025] changing syslog mask from 0xff to 0x7f
    <3>[ 18.029] dhcpcd[115]: dhcpcd not running
    <4>[ 18.039] changing syslog mask from 0xff to 0x7f
    <6>[ 18.041] dhcpcd[117]: version 6.4.2 starting
    <6>[ 18.043] dhcpcd[117]: eth0: adding address fe80::92ac:3fff:fe02:adb
    <6>[ 18.044] dhcpcd[117]: forked to background, child pid 119
    <4>[ 18.055] No inbound bandwidth shaping on eth0
    <6>[ 18.124] DHCP NOCARRIER eth0 down
    <4>[ 18.264] net-configure: eth0 update
    <7>[ 18.289] __clk_enable: network [1]
    <7>[ 18.289] bcm7425_pm_network_enable 00
    <7>[ 18.289] __clk_enable: enet [1]
    <7>[ 18.289] bcm40nm_pm_genet_enable 00
    <6>[ 18.459] ADDRCONF(NETDEV_UP): eth0: link is not ready
    <6>[ 18.459] dhcpcd[119]: eth0: waiting for carrier
    <4>[ 18.464] Loading Broadcom WiFi:
    <6>[ 18.688] usbcore: registered new interface driver dbus_usbdev
    <4>[ 18.689] Broadcom WiFi not found
    <4>[ 18.746] Starting ptp4l on domain 0...
    <4>[ 18.794] Starting ptp4l as slave-only
    <4>[ 18.794] done
    <4>[ 18.812] ptp4l: port 1: get_ts_info not supported
    <4>[ 18.813] ptp4l: port 1: INITIALIZING to LISTENING on INITIALIZE
    <4>[ 18.813] ptp4l: port 0: INITIALIZING to LISTENING on INITIALIZE
    <4>[ 18.831] net.ipv4.conf.eth0.force_igmp_version = 0
    <4>[ 19.454] Starting extensions message bus:
    <4>[ 19.465] dbus.
    <4>[ 19.469] Skipping non-extension UBI writable
    <4>[ 19.470] Skipping non-extension UBI rootfs
    <4>[ 19.514] Feature 'EAC3' not set
    <4>[ 19.545] Feature 'AC3' not set
    <4>[ 19.581] share-terminal: serial console only
    <4>[ 19.584] Starting BrightSign application...
    <6>[ 20.070] bcmgenet bcmgenet.0: eth0: link up, 100 Mbps, full duplex
    <6>[ 20.070] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    <6>[ 20.071] dhcpcd[119]: eth0: carrier acquired
    <4>[ 20.236] net-configure: eth0 update
    <3>[ 20.271] dhcpcd[119]: error writing DUID: /etc/dhcpcd.duid: Read-only file system
    <6>[ 20.271] dhcpcd[119]: DUID 00:03:00:01:90:ac:3f:02:0a:db
    <6>[ 20.271] dhcpcd[119]: eth0: IAID 3f:02:0a:db
    <6>[ 20.328] dhcpcd[119]: eth0: soliciting an IPv6 router
    <6>[ 21.180] dhcpcd[119]: eth0: soliciting a DHCP lease
    <6>[ 21.561] dhcpcd[119]: eth0: Router Advertisement from fe80::d604:cdff:fe8a:9d10
    <6>[ 21.561] dhcpcd[119]: eth0: adding address 2602:306:392a:a280:92ac:3fff:fe02:adb/64
    <6>[ 21.561] dhcpcd[119]: eth0: soliciting a DHCPv6 lease
    <6>[ 21.663] dhcpcd[119]: eth0: ADV 2602:306:392a:a280::45/128 from fe80::d604:cdff:fe8a:9d10
    <6>[ 21.673] dhcpcd[119]: eth0: REPLY6 received from fe80::d604:cdff:fe8a:9d10
    <6>[ 21.673] dhcpcd[119]: eth0: adding address 2602:306:392a:a280::45/128
    <6>[ 21.673] dhcpcd[119]: eth0: renew in 302400 seconds, rebind in 483840 seconds
    <6>[ 22.184] dhcpcd[119]: eth0: offered 192.168.1.83 from 192.168.1.254
    <6>[ 23.632] DHCP BOUND6 eth0 ip= dns=
    <4>[ 23.744] net-configure: eth0 update
    <4>[ 24.814] ptp4l: selected best master clock 90ac3f.fffe.020adb
    <4>[ 25.550] BrightSign application cheetah-6.1.76 starting
    <4>[ 25.922] ### 00:00:00.253 nexus_platform_settings: Overwriting heap[2].size -1 with memconfig value
    <4>[ 25.922] ### 00:00:00.253 nexus_platform_settings: Overwriting heap[3].size -1 with memconfig value
    <4>[ 25.922] Maximum audio sample rate supported: 48000Hz
    <4>[ 25.923] *** 00:00:00.000 nexus_platform: cheetah 15.3 boxmode 0
    <4>[ 25.928] *** 00:00:00.005 BCHP_PWR:
    <4>[ 25.928] *** 00:00:00.005 BCHP_PWR: ****************************************
    <4>[ 25.928] *** 00:00:00.005 BCHP_PWR: ****************************************
    <4>[ 25.928] *** 00:00:00.005 BCHP_PWR: ** BCHP_PWR POWER MANAGEMENT DISABLED **
    <4>[ 25.928] *** 00:00:00.005 BCHP_PWR: ****************************************
    <4>[ 25.928] *** 00:00:00.005 BCHP_PWR: ****************************************
    <4>[ 25.929] *** 00:00:00.006 BCHP_PWR:
    <4>[ 25.929] *** 00:00:00.006 BCHP: BCHP_Open7425: Setting TX CEC_ADDRxx register fields to 0x15 (Unregistered) address
    <4>[ 25.929] *** 00:00:00.006 BCHP: BCHP_Open7425: Setting RX CEC_ADDRxx register fields to 0x15 (Unregistered) address
    <4>[ 25.933] *** 00:00:00.010 nexus_platform_interrupt: Exceeded number of slots for external IRQ (5,5), ignoring 11
    <4>[ 25.933] *** 00:00:00.010 nexus_platform_interrupt: Exceeded number of slots for external IRQ (5,5), ignoring 12
    <4>[ 25.933] *** 00:00:00.010 nexus_platform_interrupt: Exceeded number of slots for external IRQ (5,5), ignoring 13
    <4>[ 25.933] *** 00:00:00.010 nexus_platform_interrupt: Exceeded number of slots for external IRQ (5,5), ignoring 14
    <4>[ 25.933] *** 00:00:00.010 nexus_platform_interrupt: Exceeded number of slots for external IRQ (5,5), ignoring 15
    <4>[ 25.933] *** 00:00:00.010 nexus_platform_interrupt: Exceeded number of slots for external IRQ (5,5), ignoring 16
    <4>[ 25.958] *** 00:00:00.035 BHSM: RAVE Verification OTP [078] [00][00][00][00].
    <4>[ 25.959] *** 00:00:00.036 BHSM: SID Verification OTP [142] [00][00][00][00].
    <4>[ 25.959] *** 00:00:00.036 BHSM: RAAGA A Verification OTP [076] [00][00][00][00].
    <4>[ 25.960] *** 00:00:00.037 BHSM: VIDEO Verification OTP [077] [00][00][00][00].
    <4>[ 25.960] *** 00:00:00.037 BHSM: VICE Verification OTP [131] [00][00][00][00].
    <4>[ 25.961] *** 00:00:00.038 BHSM: EK3 Verification OTP [055] [00][00][00][00].
    <4>[ 25.961] *** 00:00:00.038 BHSM: BSP Platform[2.0.0] BSECK[1.0.0] modes[0x00]
    <4>[ 25.972] *** 00:00:00.049 nexus_transport: DPCR Thread: started
    <4>[ 26.276] *** 00:00:00.353 nexus_statistics_module: file[High] modules/file/src/nexus_file_scheduler.c:473 117250 usec
    <4>[ 26.384] *** 00:00:00.461 BXVD: BXVD_Open() - Hardware revision: L, Firmware revision: 16050f
    <4>[ 26.428] *** 00:00:00.505 BXVD: BXVD_Open() - Hardware revision: L, Firmware revision: 16050f
    <4>[ 26.464] *** 00:00:00.541 nexus_i2c: Channel 5 is not available on this platoform.
    <4>[ 26.465] *** 00:00:00.542 nexus_i2c: Channel 6 is not available on this platoform.
    <4>[ 26.482] *** 00:00:00.559 BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1440 x 900 ( 900p)
    <4>[ 26.482] *** 00:00:00.559 BHDM_EDID: No EDID Extensions Found... Monitor supports DVI (Video) only
    <4>[ 26.582] *** 00:00:00.659 nexus_hdmi_output: Read EDID Try 1 of 3
    <4>[ 26.596] *** 00:00:00.673 BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1440 x 900 ( 900p)
    <4>[ 26.596] *** 00:00:00.673 BHDM_EDID: No EDID Extensions Found... Monitor supports DVI (Video) only
    <4>[ 26.696] *** 00:00:00.773 nexus_hdmi_output: Read EDID Try 2 of 3
    <4>[ 26.709] *** 00:00:00.786 BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1440 x 900 ( 900p)
    <4>[ 26.709] *** 00:00:00.786 BHDM_EDID: No EDID Extensions Found... Monitor supports DVI (Video) only
    <4>[ 26.822] *** 00:00:00.899 BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1440 x 900 ( 900p)
    <4>[ 26.822] *** 00:00:00.899 BHDM_EDID: No EDID Extensions Found... Monitor supports DVI (Video) only
    <4>[ 26.922] ### 00:00:00.999 nexus_hdmi_output: Unable to read EDID after 4 attempts
    <4>[ 26.922] *** 00:00:00.999 nexus_statistics_module: hdmi_output[Low] nexus/base/src/nexus_base_scheduler.c:828 404226 usec
    <4>[ 26.923] *** 00:00:01.000 nexus_statistics_callback: Timer callback 0xdf0050:0x765a60dc from modules/hdmi_output/src/nexus_hdmi_output.c:2090 404366 usec
    <4>[ 26.923] *** 00:00:01.000 nexus_statistics_api: NEXUS_HdmiOutput_Open[hdmi_output:Low] 454291 usec
    <4>[ 26.923] *** 00:00:01.000 nexus_platform: initialized
    <4>[ 26.923] *** 00:00:01.000 nexus_statistics_module: platform[High] nexus/base/src/nexus_base_scheduler.c:828 497723 usec
    <4>[ 26.924] *** 00:00:01.001 nexus_statistics_callback: Timer callback 0xd9c3a0:0x76439cec from common/src/linuxuser/nexus_platform_os.c:673 497835 usec
    <4>[ 26.924] *** 00:00:01.001 nexus_timebase: Unsupported frameRateCode of 0; using 60000/1001
    <4>[ 26.924] ### 00:00:01.001 nexus_timebase: NEXUS_Timebase_P_SetSettings: Unknown sample rate 0, assuming 48000
    <4>[ 26.934] *** 00:00:01.011 xpt_pcr: Changing to non-PCR source
    <4>[ 26.995] !!!Error (0x110001) at magnum/portinginterface/i2c/src/bi2c.c:921
    <4>[ 26.995] !!!Error (0x110001) at magnum/portinginterface/i2c/src/bi2c.c:921
    <4>[ 26.996] *** 00:00:01.073 BHDM_EDID: No BCM Supported Detail/Preferred Timing Descriptors found; selecting an alternate...
    <4>[ 26.996] *** 00:00:01.073 BHDM_EDID: Selecting alternate supported BCM supported format: BFMT_VideoFmt_eDVI_1024x768p
    <4>[ 27.039] NetworkTime: server changed to 'http://time.brightsignnetwork.com'
    <4>[ 27.039] NetworkTime: Configuration changed.
    <4>[ 27.066] commandline read: brightsign
    <4>[ 27.073] ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.17 |~~~~~~~~~~~~~~~~~~~~~~~~~~
    <4>[ 27.073] (c) 2001-2012 The world wide DirectFB Open Source Community
    <4>[ 27.073] (c) 2000-2004 Convergence (integrated media) GmbH
    <4>[ 27.073] ----------------------------------------------------------------
    <4>[ 27.073]
    <4>[ 27.096] (*) DirectFB/Core: Single Application Core. (2016-02-19 19:46) [ DEBUG ]
    <4>[ 27.166] *** 00:00:00.000 platform_init: Broadcom Corporation DirectFB Platform Layer Version 7.0
    <4>[ 27.166] *** 00:00:00.000 nexus_common_init: Display heap: handle=0xda2780 size 305356kB - free 288972kB - largest block 288972kB
    <4>[ 27.166] *** 00:00:00.000 nexus_common_init: Offscreen heap: handle=0xda2780 size 305356kB - free 288972kB - largest block 288972kB
    <4>[ 27.210] (*) DirectFB/Graphics: Broadcom Corporation Bcmnexus Packet Buffer GFX Driver 4.3 (Broadcom Corporation)
    <4>[ 27.299] (*) Direct/Thread: Started 'BRCM NotifyDisplay' (-1) [OUTPUT OTHER/OTHER 0/0] <1048576>...
    <4>[ 27.320] (*) DirectFB/Core/WM: Default 0.3 (directfb.org)
    <4>[ 27.435] 00:00:00.268 BHDM: Tx0: Output Fmt: 1080i (RGB (Default) 24 bpp) 1920 [+] x 540/540 [+]
    <4>[ 27.435] 00:00:00.268 BHDM: Tx0: Pixel Clock: 74 MHz (TMDS Character Rate 148 Mcsc)
    <4>[ 27.435] 00:00:00.268 BHDM: Tx0: Output Mode: DVI (Video Only)
    <4>[ 27.436] *** 00:00:00.270 BHDM_EDID: No BCM Supported Detail/Preferred Timing Descriptors found; selecting an alternate...
    <4>[ 27.436] *** 00:00:00.270 BHDM_EDID: Selecting alternate supported BCM supported format: BFMT_VideoFmt_eDVI_1024x768p
    <4>[ 27.468] 00:00:00.301 BHDM: Tx0: Output Fmt: 1080p (RGB (Default) 24 bpp) 1920 [+] x 1080/1080 [+]
    <4>[ 27.468] 00:00:00.301 BHDM: Tx0: Pixel Clock: 148 MHz (TMDS Character Rate 148 Mcsc)
    <4>[ 27.468] 00:00:00.301 BHDM: Tx0: Output Mode: DVI (Video Only)
    <4>[ 27.485] *** 00:00:00.318 platform_nexus_display: HDMI hotplug event: connected
    <6>[ 27.662] dhcpcd[119]: eth0: leased 192.168.1.83 for 86400 seconds
    <6>[ 27.663] dhcpcd[119]: eth0: adding route to 192.168.1.0/24
    <6>[ 27.663] dhcpcd[119]: eth0: adding default route via 192.168.1.254
    <6>[ 27.676] DHCP BOUND eth0 ip=192.168.1.83 nm=255.255.255.0 gw=192.168.1.254 domain=attlocal.net dns=192.168.1.254
    <4>[ 27.876] net-configure: eth0 update
    <4>[ 27.908] *** 00:00:00.741 nexus_hdmi_output: RxSense checking is finished; Rx is powered down...
    <4>[ 27.908] *** 00:00:00.742 nexus_hdmi_output: RxSense polling timer is already running!
    <6>[ 27.912] dhcpcd[119]: eth0: removing route to 192.168.1.0/24
    <4>[ 27.939] *** 00:00:00.772 BCHP_AVS: Booted with CFE that doesn't include AVS support --- disabling AVS!
    <4>[ 28.875] sys_close: 4075 callbacks suppressed
    <3>[ 28.875] NetworkTimeThre(342):close(21) returning EBADF
    <4>[ 29.010] SignalDispatcher received signal 18
    <4>[ 29.011] Setting clock since we're not a PTP slave and difference is greater than two seconds.
    <4>[ 29.011] Setting system clock to 1477509532.000000
    <4>[ 29.015] NetworkTime: clock set to 2016/10/26 19:18:52.004 UTC
    <4>[ 30.288] *** 00:00:03.765 BHDM_EDID: No BCM Supported Detail/Preferred Timing Descriptors found; selecting an alternate...
    <4>[ 30.288] *** 00:00:03.765 BHDM_EDID: Selecting alternate supported BCM supported format: BFMT_VideoFmt_eDVI_1024x768p
    <4>[ 30.303] *** 00:00:03.780 BHDR_EDID_RAM: HDMI EDID bytes not specified (=NULL); using default EDID
    <4>[ 30.324] *** 00:00:03.801 BHDR_HDCP_PRIV: HDCP Key Set invalid/not loaded to RAM
    <4>[ 30.324] *** 00:00:03.801 BHDR_HDCP_PRIV: HDCP BKsv Valid: 0
    <4>[ 30.324] *** 00:00:03.801 BHDR_HDCP_PRIV: HDCP Keys loaded to RAM: 0
    <4>[ 30.324] 00:00:03.801 nexus_hdmi_input_hdcp: Begin Loading Encrypted keyset...
    <4>[ 30.352] 00:00:03.829 nexus_hdmi_input_hdcp: Done Loading Encrypted keyset...
    <4>[ 30.353] No DTCP key flashed
    <4>[ 30.362] *** DTCP-IP failed to initialise - DTCP-IP will not be available ***
    <6>[ 30.661] xc5000: waiting for firmware upload (dvb-fe-xc5000c-6.1.16400.fw)...
    <7>[ 30.699] xc5000: firmware read 16503 bytes.
    <6>[ 30.699] xc5000: firmware uploading...
    <6>[ 34.176] xc5000: firmware upload complete...
    <4>[ 96.838] *** 00:01:10.315 xpt_pcr: Finished change to non-PCR source
    <4>[ 96.841] *** 00:01:10.317 xpt_pcr: Changing to non-PCR source
    <4>[ 96.926] *** 00:01:10.403 xpt_pcr: Finished change to non-PCR source
    <4>[ 350.267] 00:05:23.743 BHDM: Tx0: Output Fmt: 1080p (RGB (Default) 24 bpp) 1920 [+] x 1080/1080 [+]
    <4>[ 350.267] 00:05:23.744 BHDM: Tx0: Pixel Clock: 148 MHz (TMDS Character Rate 148 Mcsc)
    <4>[ 350.267] 00:05:23.744 BHDM: Tx0: Output Mode: DVI (Video Only)
    <4>[ 350.286] *** 00:05:23.762 BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1440 x 900 ( 900p)
    <4>[ 350.286] *** 00:05:23.762 BHDM_EDID: No EDID Extensions Found... Monitor supports DVI (Video) only
    <4>[ 350.386] *** 00:05:23.863 nexus_hdmi_output: Read EDID Try 1 of 3
    <4>[ 350.399] *** 00:05:23.876 BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1440 x 900 ( 900p)
    <4>[ 350.399] *** 00:05:23.876 BHDM_EDID: No EDID Extensions Found... Monitor supports DVI (Video) only
    <4>[ 350.499] *** 00:05:23.976 nexus_hdmi_output: Read EDID Try 2 of 3
    <4>[ 350.512] *** 00:05:23.989 BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1440 x 900 ( 900p)
    <4>[ 350.512] *** 00:05:23.989 BHDM_EDID: No EDID Extensions Found... Monitor supports DVI (Video) only
    <4>[ 350.626] *** 00:05:24.102 BHDM_EDID: Unknown/Unsupported Detailed Timing Format 1440 x 900 ( 900p)
    <4>[ 350.626] *** 00:05:24.102 BHDM_EDID: No EDID Extensions Found... Monitor supports DVI (Video) only
    <4>[ 350.726] ### 00:05:24.202 nexus_hdmi_output: Unable to read EDID after 4 attempts
    <4>[ 350.726] ### 00:05:24.202 nexus_base: lock held 453ms: hdmi_output(nexus/base/src/nexus_base_scheduler.c:947), last lock:hdmi_output(nexus/base/src/nexus_base_scheduler.c:942)
    <4>[ 350.726] ### 00:05:24.202 nexus_base: (also 4 occurrences not reported
    <4>[ 350.726] *** 00:05:24.203 nexus_statistics_callback: Event callback 0xdeffd8:0x765a6588 from modules/hdmi_output/src/nexus_hdmi_output.c:485 453228 usec
    <4>[ 350.830] *** 00:05:24.306 BHDM_EDID: No BCM Supported Detail/Preferred Timing Descriptors found; selecting an alternate...
    <4>[ 350.830] *** 00:05:24.306 BHDM_EDID: Selecting alternate supported BCM supported format: BFMT_VideoFmt_eDVI_1024x768p
    <4>[ 350.830] *** 00:05:24.307 nexus_statistics_callback: TaskCallback callback 0xdedc60:0x76441598 from modules/hdmi_output/src/nexus_hdmi_output.c:386 100742 usec
    <6>[ 361.527] mmc0: going to HIGHSPEED mode
    <6>[ 361.528] mmc0: new high speed SDHC card at address b368
    <6>[ 361.530] mmcblk0: mmc0:b368 7.45 GiB
    <6>[ 361.533] mmcblk0: p1
    <4>[ 361.554] usbmount-414: mount mmcblk0 /devices/platform/sdhci-brcmstb.0/mmc_host/mmc0/mmc0:b368/block/mmcblk0
    <4>[ 361.557] usbmount-414: path='/sys/devices/platform/sdhci-brcmstb.0/mmc_host/mmc0/mmc0:b368'
    <6>[ 361.561] mmcblk0: p1
    <4>[ 361.576] Disk /dev/mmcblk0: 8010 MB, 8010072064 bytes
    <4>[ 361.576] 214 heads, 8 sectors/track, 9138 cylinders, total 15644672 sectors
    <4>[ 361.576] Units = sectors of 1 * 512 = 512 bytes
    <4>[ 361.576]
    <4>[ 361.576] Device Boot Start End Blocks Id System
    <4>[ 361.576] /dev/mmcblk0p1 8192 15644671 7818240 b Win95 FAT32
    <4>[ 361.582] usbmount-414: Considering /dev/mmcblk0p4...
    <4>[ 361.584] usbmount-414: Considering /dev/mmcblk0p3...
    <4>[ 361.586] usbmount-414: Considering /dev/mmcblk0p2...
    <4>[ 361.589] usbmount-414: Considering /dev/mmcblk0p1...
    <4>[ 361.591] usbmount-414: /dev/mmcblk0p1 is a valid block device
    <4>[ 361.679] ID_FS_LABEL=BS_3
    <4>[ 361.679] ID_FS_LABEL_ENC=BS_3
    <4>[ 361.679] ID_FS_UUID=5C34-9F40
    <4>[ 361.679] ID_FS_UUID_ENC=5C34-9F40
    <4>[ 361.679] ID_FS_TYPE=vfat
    <4>[ 361.736] usbmount-414: Filesystem on /dev/mmcblk0p1
    <4>[ 361.795] usbmount-414: ID_FS_TYPE=vfat
    <4>[ 361.802] usbmount-414: device_size=15636480
    <4>[ 361.802] usbmount-414: fsck_timeout=54
    <4>[ 362.985] fsck.fat 3.0.25 (2014-01-17)
    <4>[ 362.985] /dev/mmcblk0p1: 152 files, 15757/1950464 clusters
    <4>[ 362.997] timely: /sbin/dosfsck exited with 0 after 1s
    <4>[ 362.998] usbmount-414: fsck.vfat /dev/mmcblk0p1 succeeded
    <4>[ 363.012] usbmount-414: Successfully mounted /dev/mmcblk0p1 at /storage/sd.fwup
    <4>[ 363.013] usbmount-414: Cleaned up fsck cruft at /storage/sd.fwup
    <4>[ 363.086] usbmount-414: Looking for firmware update at /storage/sd.fwup
    <4>[ 363.137] No appropriate upgrade files found.
    <4>[ 363.138] usbmount-414: Migrating mounted filesystem from /storage/sd.fwup to /storage/sd
    <4>[ 363.141] Checking for network recovery override.
    <4>[ 363.145] Looking for recovery script at 'http://handlers.unifirst.ds//recovery/recovery.ashx'
    <4>[ 363.550] Recovery server response code: 200
    <4>[ 363.551] Running recovery script from server
    <4>[ 363.587] Loading 'TMP:/recovery1.brs' (65ba9dad268cc9b7f920a652a674f55074bc0a3b)
    <4>[ 363.589] Sending error report to http://handlers.unifirst.ds//bs/error.ashx
    <4>[ 363.970] Failed to send error report to network: 404
    <4>[ 363.970] ScriptLoadError: Syntax Error. (compile error &h02) in TMP:/recovery1.brs(1)
    <4>[ 363.970] ScriptName: TMP:/recovery1.brs
    <4>[ 363.970] ScriptHash: 65ba9dad268cc9b7f920a652a674f55074bc0a3b
    <4>[ 363.970] Press SVC button to interrupt.
    <4>[ 385.122] Requesting reboot via init.
    <4>[ 385.126] Telling brightsign application at pid 261 to go away.
    <4>[ 385.126] SignalDispatcher received signal 15
    <4>[ 385.126] BrightSign application cheetah-6.1.76 fast exit
    <2>[ 385.139] bcm74xx_wdt: Unexpected close, not stopping watchdog!
    <2>[ 385.634] bcm74xx_wdt: Unexpected close, not stopping watchdog!
    <4>[ 385.638] Stopping: /etc/rc2.d/K97mount-features.sh
    <4>[ 385.639] Stopping: /etc/rc2.d/K97customer-hook.sh
    <4>[ 385.641] Stopping: /etc/rc2.d/K96dbus-1-extensions
    <4>[ 385.643] Stopping extensions message bus:
    <4>[ 385.646] dbus.
    <4>[ 385.648] Stopping: /etc/rc2.d/K71httpd.sh
    <4>[ 385.656] Stopping: /etc/rc2.d/K60crashdump.sh
    <4>[ 385.658] Stopping: /etc/rc2.d/K39wifi.sh
    <4>[ 385.658] Stopping dhcpcd wlan0
    <4>[ 385.706] net-configure: wlan0 stop
    <4>[ 385.727] net-configure: EXCEPTION: Unknown network interface name: wlan0
    <4>[ 385.729] Script /etc/rc2.d/K39wifi.sh stop failed 2
    <4>[ 385.729] Stopping: /etc/rc2.d/K35coldplug-usb.sh
    <4>[ 385.730] Stopping: /etc/rc2.d/K34coldplug-modems.sh
    <4>[ 385.731] Stopping: /etc/rc2.d/K33lldp-brightsign
    <4>[ 385.733] Stopping: /etc/rc2.d/K31dhcpcd.sh
    <4>[ 385.766] Stopping dhcpcd eth0
    <4>[ 385.812] net-configure: eth0 stop
    <4>[ 385.842] sys_close: 1002 callbacks suppressed
    <3>[ 385.842] net-configure(487):close(8) returning EBADF
    <4>[ 385.845] changing syslog mask from 0xff to 0x7f
    <6>[ 385.847] dhcpcd[487]: sending signal TERM to pid 119
    <6>[ 385.847] dhcpcd[119]: received signal TERM from PID 487, stopping
    <6>[ 385.847] dhcpcd[119]: eth0: removing interface
    <6>[ 385.847] dhcpcd[119]: eth0: deleting address 2602:306:392a:a280::45/128
    <6>[ 385.849] dhcpcd[487]: waiting for pid 119 to exit
    <6>[ 385.853] DHCP STOP6 unexpected
    <6>[ 385.871] dhcpcd[119]: eth0: deleting address 2602:306:392a:a280:92ac:3fff:fe02:adb/64
    <6>[ 385.894] dhcpcd[119]: eth0: deleting default route via 192.168.1.254
    <6>[ 385.899] DHCP STOP eth0 down
    <6>[ 385.913] dhcpcd[119]: exited
    <4>[ 385.951] Removing bandwidth shaper (if present) for eth0
    <4>[ 385.996] netlink: 20 bytes leftover after parsing attributes.
    <4>[ 385.996] netlink: 20 bytes leftover after parsing attributes.
    <4>[ 385.996] netlink: 20 bytes leftover after parsing attributes.
    <4>[ 385.996] RTNETLINK answers: No such file or directory
    <4>[ 386.000] Stopping: /etc/rc2.d/K11registry.sh
    <4>[ 386.022] Stopping: /etc/rc2.d/K02dbus-1
    <4>[ 386.024] Stopping system message bus:
    <4>[ 386.031] dbus.
    <4>[ 386.034] Unmounting file systems
    <5>[ 386.037] UBIFS: un-mount UBI device 0, volume 0
    <4>[ 386.043] umount: can't umount /storage/flash: No such file or directory
    <4>[ 386.047] umount: can't remount tmpfs read-only
    <4>[ 386.049] umount: can't remount tmpfs read-only
    <4>[ 386.049] umount: none busy - remounted read-only
    <4>[ 386.049]
    The system is going down NOW!
    <4>[ 386.050] ptp4l: caught signal 15
    <4>[ 386.053]
    Sent SIGTERM to all processes
    <4>[ 387.053]
    Sent SIGKILL to all processes
    <4>[ 387.054]
    Unmounted /dev/shm
    <4>[ 387.055]
    Unmounted /sys
    <4>[ 387.056]
    Unmounted /var/volatile
    <4>[ 387.056]
    Unmounted /proc
    <4>[ 387.056]
    Unmounted /
    <4>[ 387.056] init: none busy - remounted read-only
    <4>[ 387.056]
    Unmounted /dev
    <4>[ 387.056]
    Unmounted /
    <4>[ 387.056]
    All filesystems are now unmounted
    <4>[ 387.056]
    Requesting system reboot
    <0>[ 388.060] Restarting system.


    www.brightsign.biz | ©2015 BrightSign

    Edited by Kevin Gage
  • 0
    Avatar
    Kevin Gage

    What does the log tell you about this error?

  • 0
    Avatar
    Lyndon

    The log says the unit's crashing in the recovery script. usually, that only happens if there's a registry problem. 

     

    If you power up with no sd card, you get the same 10 flashes?

    I would reset the unit to factory defaults, and see if it still fails.

    Then, if it boots fine, redo the brightsign network setup for that player with diagnostics enabled for setup. I want to see if it is able to boot fine before setup, and then if the ethernet test fails.

  • 0
    Avatar
    Kevin Gage

    w/o card: powers-up fine

    When I try to default the unit using this method, I still get the 10 flashes.

    What can I try next?

     

  • 0
    Avatar
    Kevin Gage

    .

  • 1
    Avatar
    Lyndon

    First, reset unit to Factory Defaults:
    http://support.brightsign.biz/entries/21796878-How-do-I-restore-reset-a-unit-to-Factory-Default-settings-

     

    Then copy this autorun zip to a blank card, and power up the unit. 

     

    SD card:
    https://www.brightsignnetwork.com/download/Tools/hdmitest720p/SDCard/autorun.zip

  • 0
    Avatar
    Kevin Gage

    FROM MY LAST ENTRY: When I try to default the unit using this method, I still get the 10 flashes.

  • 0
    Avatar
    Lyndon

    And, your card's formatted fat32? Please send a screenshot of what's on the sd card when you get the errors. Please send the file from your sd card as well. 

  • 0
    Avatar
    Kevin Gage

    FAT32, Yes.

    The only file on the card is the "autorun.brs" DL'd from the "Performing a factory reset" page.

  • 0
    Avatar
    Kevin Gage

    After running through the process again, the player seems to have read "autorun.brs" and restored itself.

    I was also able to load the "autorun.zip" demo file above and get it to run.

    I'm not sure what changed but the unit seems to be working now.

    Thanks.

    Kevin G

     

  • 0
    Avatar
    Lyndon

     

    Let us know if the unit starts erroring out again

    Edited by Lyndon
  • 0
    Avatar
    Sarah Lewison

    this is what is happening to me. 10 flashes. I updated the firmware already 

  • 0
    Avatar
    Filippo Centenari

    I have same issue on xd234 always worked.
    Now no simple file network and 10 red lights

    the autorun.zip files provide by Lyndon works on my sd card

     

    what to try?

  • 0
    Avatar
    Rob Burgoyne

    I get this error on our XD1034 units that are about 800 miles away. By reading this old and long thread it looks like I am taking an expensive road trip to reset to defaults, format the sd card and copy a new autorun.zip to the card. Why? Hasn't? This? Bug? Been? Fixed? You have had at least 6 years to do so.

    If there is a better, easier OR REMOTE way to do this please reply.

Please sign in to leave a comment.
Can't find what you're looking for? Try to
Contact support
Powered by Zendesk