So I have read through numerous posts and tried various things however I cannot get sound to come through the video stream.
Setup -
DishNetwork TV receiver passing video signal to HDMI matrix
(Audio on receiver is set to PCM only)
HDMI over Ethernet extender
HDMI into XT1143 player
When i first sent the simple presentation (testing so just Live Video zone ) to the player i had sound for a few minutes and then it was gone. I have tried various audio settings in the presentation but no change. When selecting Fixed Audio it freaks out the player and it just consistently reboots. Video is good signal. Signal works fine directly into TV set.
I have read through the log file but don't really know what i am looking for. I did see some errors however i don't really know what they mean.
Any Help would be appreciated.
Thank you,
Anthony
Player info
Boot Version: 7.0.16
Boot Extra Version: 7.0.60
Firmware Version: 7.0.60
Video Mode: 4096x2160x60p (4096x2160x60p)
Log file -
[ 0.000] Booting Linux on physical CPU 0x0
[ 0.000] Linux version 3.14.28-1.16+bs7.0.60 (jenkins@scoop) (gcc version 6.3.0 (GCC) ) #1 SMP Fri Feb 2 10:24:43 GMT 2018
[ 0.000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=50c53c7d
[ 0.000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000] Machine model: impala
[ 0.000] moving dtb from 0x08000000 to 0x00b7f038
[ 0.000] BMEM 1/3 region 0 allocate size=0x27000000 @ 0x10000000 BMEM in memory bank start=0x10000000, size=0x70000000
[ 0.000] BMEM 1/3 region 1 allocate size=0x20000000 @ 0x60000000 CMA in memory bank start=0x10000000, size=0x70000000
[ 0.000] BMEM 2/3 region 0 allocate size=0x20000000 @ 0x80000000 CMA in memory bank start=0x80000000, size=0x40000000
[ 0.000] BMEM 2/3 region 1 allocate size=0x1ab00000 @ 0xa0000000 BMEM in memory bank start=0x80000000, size=0x40000000
[ 0.000] cma_driver: cma_reserve cma-default 0 n_cma_regions 2 override defaults 0
[ 0.000] cma: cma_declare_contiguous(size 0x20000000, base 0x60000000, limit 0x00000000 alignment 0x00000000)
[ 0.000] cma: Reserved 512 MiB at 0x60000000
[ 0.000] cma: cma_declare_contiguous(size 0x20000000, base 0x80000000, limit 0x00000000 alignment 0x00000000)
[ 0.000] cma: Reserved 512 MiB at 0x80000000
[ 0.000] BMEM 1/3 region 0 allocate size=0x27000000 @ 0x10000000 BMEM in memory bank start=0x10000000, size=0x70000000
[ 0.000] BMEM 1/3 region 1 allocate size=0x20000000 @ 0x60000000 CMA in memory bank start=0x10000000, size=0x70000000
[ 0.000] BMEM 2/3 region 0 allocate size=0x20000000 @ 0x80000000 CMA in memory bank start=0x80000000, size=0x40000000
[ 0.000] BMEM 2/3 region 1 allocate size=0x1ab00000 @ 0xa0000000 BMEM in memory bank start=0x80000000, size=0x40000000
[ 0.000] bmem: Reserved 624 MiB at 0x10000000
[ 0.000] bmem: Reserved 427 MiB at 0xa0000000
[ 0.000] cma: dma_contiguous_reserve(limit 10000000)
[ 0.000] Memory policy: Data cache writealloc
[ 0.000] On node 0 totalpages: 786432
[ 0.000] free_area_init_node: node 0, pgdat c089b5c0, node_mem_map ce7f9000
[ 0.000] Normal zone: 512 pages used for memmap
[ 0.000] Normal zone: 0 pages reserved
[ 0.000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000] HighMem zone: 5632 pages used for memmap
[ 0.000] HighMem zone: 720896 pages, LIFO batch:31
[ 0.000] MCP: Disabling write pairing
[ 0.000] PERCPU: Embedded 9 pages/cpu @ce7c3000 s12480 r8192 d16192 u36864
[ 0.000] pcpu-alloc: s12480 r8192 d16192 u36864 alloc=9*4096
[ 0.000] pcpu-alloc: [0] 0 [0] 1
[ 0.000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 785920
[ 0.000] Kernel command line:
[ 0.000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000] Memory: 984100K/3145728K available (5129K kernel code, 426K rwdata, 2412K rodata, 924K init, 534K bss, 1113052K reserved, 1048576K cma-reserved, 758784K highmem)
[ 0.000] Virtual kernel memory layout:
[ 0.000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB)
[ 0.000] .text : 0xc0008000 - 0xc0765988 (7543 kB)
[ 0.000] .init : 0xc0766000 - 0xc084d0c0 ( 925 kB)
[ 0.000] .data : 0xc084e000 - 0xc08b89f0 ( 427 kB)
[ 0.000] .bss : 0xc08b89f0 - 0xc093e5d0 ( 535 kB)
[ 0.000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000] Hierarchical RCU implementation.
[ 0.000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000] NR_IRQS:16 nr_irqs:16 16
[ 0.000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93)
[ 0.000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
[ 0.000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95)
[ 0.000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58)
[ 0.000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xfc40a700, parent IRQ(s): 2)
[ 0.000] irq_bcm7120_l2: registered BCM7120 L2 intc (mem: 0xfc417380, parent IRQ(s): 3)
[ 0.000] Architected cp15 timer(s) running at 27.00MHz (virt).
[ 0.000] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
[ 0.000] Switching to timer-based delay loop
[ 0.000] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=270000)
[ 0.000] pid_max: default: 32768 minimum: 301
[ 0.000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.007] CPU: Testing write buffer coherency: ok
[ 0.007] ftrace: allocating 24289 entries in 48 pages
[ 0.026] CPU0: update cpu_power 1024
[ 0.026] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.026] Setting up static identity map for 0x4d65a0 - 0x4d65d0
[ 0.029] CPU1: Booted secondary processor
[ 0.029] CPU1: update cpu_power 1024
[ 0.029] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.029] Brought up 2 CPUs
[ 0.029] SMP: Total of 2 processors activated.
[ 0.029] CPU: All CPU(s) started in SVC mode.
[ 0.029] devtmpfs: initialized
[ 0.033] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
[ 0.052] regulator-dummy: no parameters
[ 0.052] NET: Registered protocol family 16
[ 0.053] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.053] cpuidle: using governor ladder
[ 0.053] cpuidle: using governor menu
[ 0.059] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] registered
[ 0.059] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
[ 0.059] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
[ 0.059] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
[ 0.059] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
[ 0.059] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
[ 0.060] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
[ 0.060] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
[ 0.060] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
[ 0.060] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
[ 0.060] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
[ 0.060] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
[ 0.060] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
[ 0.060] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
[ 0.062] hw-breakpoint: Failed to enable monitor mode on CPU 1.
[ 0.062] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
[ 0.075] bio: create slab <bio-0> at 0
[ 0.076] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159)
[ 0.076] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223)
[ 0.077] vgaarb: loaded
[ 0.077] SCSI subsystem initialized
[ 0.077] libata version 3.00 loaded.
[ 0.078] usbcore: registered new interface driver usbfs
[ 0.078] usbcore: registered new interface driver hub
[ 0.078] usbcore: registered new device driver usb
[ 0.078] Linux video capture interface: v2.00
[ 0.079] Advanced Linux Sound Architecture Driver Initialized.
[ 0.079] Bluetooth: Core ver 2.21
[ 0.079] NET: Registered protocol family 31
[ 0.079] Bluetooth: HCI device and connection manager initialized
[ 0.079] Bluetooth: HCI socket layer initialized
[ 0.079] Bluetooth: L2CAP socket layer initialized
[ 0.080] nfc: nfc_init: NFC Core ver 0.1
[ 0.080] cfg80211: Calling CRDA to update world regulatory domain
[ 0.080] NET: Registered protocol family 39
[ 0.080] brcm-pci f0460000.pcie: adjusting to legacy (broken) pcie DT
[ 0.080] brcm-pci f0460000.pcie: cannot get msi intr; MSI disabled
[ 0.080] brcm-pci f0490000.pcie: adjusting to legacy (broken) pcie DT
[ 0.080] brcm-pci f0490000.pcie: cannot get msi intr; MSI disabled
[ 0.180] brcm-pci f0460000.pcie: link down
[ 0.180] PCI host bridge to bus 0000:00
[ 0.180] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xc7ffffff]
[ 0.180] pci_bus 0000:00: root bus resource [mem 0xc8000000-0xcfffffff]
[ 0.181] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 0.181] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.181] pci 0000:00:00.0: [14e4:7439] type 01 class 0x060400
[ 0.181] brcm-pci f0460000.pcie: found device 14e4:7439 on bus 0 (PCIe0), slot 0 (irq 75)
[ 0.181] pci 0000:00:00.0: PME# supported from D0 D3hot
[ 0.181] PCI: bus0: Fast back to back transfers disabled
[ 0.181] PCI: bus1: Fast back to back transfers enabled
[ 0.181] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 0.181] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.281] brcm-pci f0490000.pcie: link down
[ 0.281] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.281] Switched to clocksource arch_sys_counter
[ 0.298] NET: Registered protocol family 2
[ 0.298] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.298] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.298] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.298] TCP: reno registered
[ 0.298] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.298] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.298] NET: Registered protocol family 1
[ 0.299] RPC: Registered named UNIX socket transport module.
[ 0.299] RPC: Registered udp transport module.
[ 0.299] RPC: Registered tcp transport module.
[ 0.299] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.299] PCI: CLS 0 bytes, default 64
[ 0.314] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[ 0.315] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.379] bounce pool size: 64 pages
[ 0.386] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.387] NTFS driver 2.1.30 [Flags: R/O].
[ 0.388] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.388] fuse init (API version 7.22)
[ 0.388] msgmni has been set to 440
[ 0.389] io scheduler noop registered
[ 0.389] io scheduler deadline registered (default)
[ 0.389] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 261, 262
[ 0.390] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device Tree
[ 0.442] PCI: enabling device 0000:00:00.0 (0000 -> 0003)
[ 0.442] aer 0000:00:00.0:pcie02: service driver aer loaded
[ 0.443] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt
[ 0.443] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded
[ 0.443] brcm-cma brcm-cma.0: Initialized Broadcom CMA root device
[ 0.443] cma: cma_alloc(cma c09271c4, count 1, align 0)
[ 0.443] cma: cma_alloc(): returned cf3f9000
[ 0.443] cma: cma_release(page cf3f9000)
[ 0.443] brcm-cma brcm-cma.0: Added CMA device @ PA=0x60000000 LEN=0x20000000
[ 0.443] cma: cma_alloc(cma c09271c4, count 131072, align 0)
[ 0.455] cma: cma_alloc(): returned cf3f9000
[ 0.455] cma_driver: cma_dev_get_mem addr 0x60000000 len 0x20000000
[ 0.455] brcm-cma brcm-cma.0: Pre-allocated 0x20000000 bytes @ 0x60000000
[ 0.455] cma: cma_alloc(cma c09271ec, count 1, align 0)
[ 0.456] cma: cma_alloc(): returned cf7f9000
[ 0.456] cma: cma_release(page cf7f9000)
[ 0.456] brcm-cma brcm-cma.1: Added CMA device @ PA=0x80000000 LEN=0x20000000
[ 0.456] cma: cma_alloc(cma c09271ec, count 131072, align 0)
[ 0.467] cma: cma_alloc(): returned cf7f9000
[ 0.467] cma_driver: cma_dev_get_mem addr 0x80000000 len 0x20000000
[ 0.467] brcm-cma brcm-cma.1: Pre-allocated 0x20000000 bytes @ 0x80000000
[ 0.468] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.469] 8250: claimed GPIO 26 for serial polarity inversion (active low)
[ 0.469] f040a940.serial: ttyS0 at MMIO 0xf040a940 (irq = 108, base_baud = 5062500) is a 16550A
[ 0.470] f040a980.serial: ttyS1 at MMIO 0xf040a980 (irq = 109, base_baud = 5062500) is a 16550A
[ 0.470] f040a900.serial: ttyS2 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
[ 0.475] brd: module loaded
[ 0.478] loop: module loaded
[ 0.479] ahci brcmstb-ahci.0: can't get clock
[ 0.479] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
[ 0.491] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 0.491] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part
[ 0.492] scsi0 : ahci_platform
[ 0.492] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
[ 0.493] brcmnand f03e2800.nand: using HIF_INTR2 cascaded IRQ
[ 0.493] brcmnand f03e2800.nand: enabling FLASH_DMA
[ 0.493] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xda
[ 0.493] nand: Unknown NAND 256MiB 3,3V 8-bit
[ 0.493] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 0.493] brcmnand f03e2800.nand: 256MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4
[ 0.493] brcmstb_nand_setup_dev: use_prefetch=1
[ 0.493] Bad block table found at page 131008, version 0x01
[ 0.494] Bad block table found at page 130944, version 0x01
[ 0.494] 7 ofpart partitions found on MTD device f03e2800.nand
[ 0.494] Creating 7 MTD partitions on "f03e2800.nand":
[ 0.494] 0x000000000000-0x000000180000 : "flash0.bolt"
[ 0.494] 0x000000180000-0x000000280000 : "flash0.nvram"
[ 0.495] 0x000000280000-0x000000400000 : "flash0.devid"
[ 0.496] 0x000000400000-0x000000e00000 : "flash0.rescue"
[ 0.496] 0x000000e00000-0x000001e00000 : "flash0.kernel"
[ 0.497] 0x000001e00000-0x000010000000 : "flash0.ubi"
[ 0.497] 0x000000000000-0x000010000000 : "flash0"
[ 0.498] ubiblk: major device number is 253
[ 0.499] libphy: Fixed MDIO Bus: probed
[ 0.500] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
[ 0.504] libphy: bcmgenet MII bus: probed
[ 0.505] PPP generic driver version 2.4.2
[ 0.505] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 0.505] usbcore: registered new interface driver pegasus
[ 0.505] usbcore: registered new interface driver asix
[ 0.505] usbcore: registered new interface driver ax88179_178a
[ 0.505] usbcore: registered new interface driver cdc_ether
[ 0.505] usbcore: registered new interface driver net1080
[ 0.506] usbcore: registered new interface driver rndis_host
[ 0.506] usbcore: registered new interface driver cdc_subset
[ 0.506] usbcore: registered new interface driver zaurus
[ 0.506] usbcore: registered new interface driver cdc_ncm
[ 0.506] ehci-brcm: EHCI BRCM driver
[ 0.506] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
[ 0.506] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 1
[ 0.516] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
[ 0.531] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
[ 0.532] hub 1-0:1.0: USB hub found
[ 0.532] hub 1-0:1.0: 1 port detected
[ 0.532] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
[ 0.532] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 2
[ 0.542] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
[ 0.561] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
[ 0.561] hub 2-0:1.0: USB hub found
[ 0.561] hub 2-0:1.0: 1 port detected
[ 0.562] ohci-brcm: OHCI BRCM driver
[ 0.562] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
[ 0.562] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 3
[ 0.562] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
[ 0.625] hub 3-0:1.0: USB hub found
[ 0.625] hub 3-0:1.0: 1 port detected
[ 0.626] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
[ 0.626] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 4
[ 0.626] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
[ 0.651] ata1: SATA link down (SStatus 0 SControl 300)
[ 0.685] hub 4-0:1.0: USB hub found
[ 0.685] hub 4-0:1.0: 1 port detected
[ 0.686] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.686] ehci-pci: EHCI PCI platform driver
[ 0.686] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.686] ohci-pci: OHCI PCI platform driver
[ 0.686] usbcore: registered new interface driver cdc_acm
[ 0.686] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.686] usbcore: registered new interface driver usblp
[ 0.686] usbcore: registered new interface driver usb-storage
[ 0.686] usbcore: registered new interface driver usbserial
[ 0.687] usbcore: registered new interface driver ch341
[ 0.687] usbserial: USB Serial support registered for ch341-uart
[ 0.687] usbcore: registered new interface driver cp210x
[ 0.687] usbserial: USB Serial support registered for cp210x
[ 0.687] usbcore: registered new interface driver ftdi_sio
[ 0.687] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 0.687] usbcore: registered new interface driver option
[ 0.687] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.687] usbcore: registered new interface driver pl2303
[ 0.687] usbserial: USB Serial support registered for pl2303
[ 0.687] usbcore: registered new interface driver sierra
[ 0.687] usbserial: USB Serial support registered for Sierra USB modem
[ 0.688] mousedev: PS/2 mouse device common for all mice
[ 0.688] input: buttons.10 as /devices/buttons.10/input/input0
[ 0.688] input_polldev: Start poll c0301dc5
[ 0.688] elo_mt_input: loaded
[ 0.688] usbcore: registered new interface driver usbtouchscreen
[ 0.688] i2c /dev entries driver
[ 0.689] brcmstb-i2c f0417300.i2c: iicc@390000hz registered in interrupt mode
[ 0.689] lirc_dev: IR Remote Control driver registered, major 251
[ 0.689] IR LIRC bridge handler initialized
[ 0.689] usbcore: registered new interface driver streamzap
[ 0.689] usbcore: registered new interface driver uvcvideo
[ 0.689] USB Video Class driver (1.1.1)
[ 0.689] gspca_main: v2.14.0 registered
[ 0.689] usbcore: registered new interface driver gspca_zc3xx
[ 0.689] usbcore: registered new interface driver Philips webcam
[ 0.689] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[ 0.689] usbcore: registered new interface driver cpia2
[ 0.690] bcm7038-wdt f040a7a8.watchdog: Registered Broadcom Watchdog
[ 0.690] sdhci: Secure Digital Host Controller Interface driver
[ 0.690] sdhci: Copyright(c) Pierre Ossman
[ 0.690] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.691] mmc0: no vqmmc regulator found
[ 0.691] mmc0: no vmmc regulator found
[ 0.741] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
[ 0.748] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.754] usbcore: registered new interface driver usbhid
[ 0.754] usbhid: USB HID core driver
[ 0.756] usbcore: registered new interface driver snd-usb-audio
[ 0.758] oprofile: using timer interrupt.
[ 0.758] drop_monitor: Initializing network drop monitor service
[ 0.758] u32 classifier
[ 0.758] Actions configured
[ 0.759] TCP: cubic registered
[ 0.761] NET: Registered protocol family 10
[ 0.763] NET: Registered protocol family 17
[ 0.767] 8021q: 802.1Q VLAN Support v1.8
[ 0.767] Key type dns_resolver registered
[ 0.768] regulator-dummy: disabling
[ 0.772] ALSA device list:
[ 0.772] No soundcards found.
[ 0.772] Warning: unable to open an initial console.
[ 0.773] Freeing unused kernel memory: 924K (c0766000 - c084d000)
[ 0.774] init (1): undefined instruction: pc=000b6248
[ 0.774] Code: f2000c40 e12fff1e f3000c40 e12fff1e (f2a00e00)
[ 0.774] init (1): undefined instruction: pc=000b6230
[ 0.774] Code: f2200150 e12fff1e ec510f1e e12fff1e (f3b00300)
[ 0.774] init (1): undefined instruction: pc=000b6238
[ 0.774] Code: ec510f1e e12fff1e f3b00300 e12fff1e (f2000c40)
[ 0.774] init (1): undefined instruction: pc=000b6240
[ 0.774] Code: f3b00300 e12fff1e f2000c40 e12fff1e (f3000c40)
[ 0.774] init (1): undefined instruction: pc=000b6228
[ 0.774] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 0.774] kmsg output is not also going to console.
[ 0.774] initramfs started...
[ 0.775] UBI: attaching mtd5 to ubi0
[ 0.851] usb 1-1: new high-speed USB device number 2 using ehci-brcm
[ 0.927] random: nonblocking pool is initialized
[ 1.007] hub 1-1:1.0: USB hub found
[ 1.007] hub 1-1:1.0: 2 ports detected
[ 1.022] mmc0: new ultra high speed DDR50 SDHC card at address e624
[ 1.023] mmcblk0: mmc0:e624 SP32G 29.7 GiB
[ 1.024] mmcblk0: p1
[ 1.191] UBI: scanning is finished
[ 1.196] UBI: attached mtd5 (name "flash0.ubi", size 226 MiB) to ubi0
[ 1.196] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.196] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.196] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.196] UBI: good PEBs: 1804, bad PEBs: 4, corrupted PEBs: 0
[ 1.196] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 1.196] UBI: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 155353000
[ 1.196] UBI: available PEBs: 386, total reserved PEBs: 1418, PEBs reserved for bad PEB handling: 36
[ 1.196] UBI: background thread "ubi_bgt0d" started, PID 795
[ 1.197] misc ubiblk_ctrl: proxying ubi0:1
[ 1.197] block ubiblk0_1: created from ubi0:1(rootfs)
[ 1.197] Verifying rootfs...
[ 9.245] Mounting rootfs from /dev/ubiblk0_1
[ 9.390] mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
[ 9.399] UBI volume is 1804 blocks
[ 9.611] UBIFS: background thread "ubifs_bgt0_0" started, PID 827
[ 9.624] UBIFS: recovery needed
[ 9.674] UBIFS: recovery completed
[ 9.674] UBIFS: mounted UBI device 0, volume 0, name "writable"
[ 9.674] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 9.674] UBIFS: FS size: 15618048 bytes (14 MiB, 123 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 9.674] UBIFS: reserved for root: 737678 bytes (720 KiB)
[ 9.674] UBIFS: media format: w4/r0 (latest is w4/r0), UUID AA013EAC-A7CE-4DDF-B329-7D6DD4F63C1E, small LPT model
[ 9.675] Using user-space nexus
[ 9.683] bcmdriver: module license 'Proprietary' taints kernel.
[ 9.683] Disabling lock debugging due to kernel taint
[ 9.683] BCMDRV: Initializing bcmdriver version $ 8
[ 9.683] BCMDRV: virtual irq: enabled (267)
[ 9.683] BCMDRV: shared gpio banks: enabled
[ 9.683] BCMDRV: Total intc words=4,Total Irqs=129
[ 9.684] BCMDRV: Initialization complete
[ 9.764] BRIGHTSIGN boot=7.0.16 firstimages=7.0.60 rescue=7.0.9 mission=7.0.60 model=XT1143 REVG serial=L8G79U001961 hw=2914f79 sk=1 sb=1
[ 9.765] AVS Revision=0.3.2.x V0=0.888V T0=53.556C PV0=0.830V MV0=0.888V
[ 9.771] Looking for crash dump:
[ 9.820] Reset causes: 0x80 reboot
[ 9.820] No post-mortem crash dump available.
[ 9.843] usbmount-864: mount mmcblk0 /devices/rdb.4/f03e0000.sdhci/mmc_host/mmc0/mmc0:e624/block/mmcblk0
[ 9.851] usbmount-864: path='/sys/devices/rdb.4/f03e0000.sdhci/mmc_host/mmc0/mmc0:e624'
[ 9.856] mmcblk0: p1
[ 9.865]
[ 9.865] Disk /dev/mmcblk0: 31.9 GB, 31914983424 bytes
[ 9.865] 255 heads, 63 sectors/track, 3880 cylinders, total 62333952 sectors
[ 9.865] Units = sectors of 1 * 512 = 512 bytes
[ 9.865]
[ 9.865] Device Boot Start End Blocks Id System
[ 9.865] /dev/mmcblk0p1 8192 62333951 31162880 c Win95 FAT32 (LBA)
[ 9.870] usbmount-864: Considering /dev/mmcblk0p4...
[ 9.872] usbmount-864: Considering /dev/mmcblk0p3...
[ 9.874] usbmount-864: Considering /dev/mmcblk0p2...
[ 9.875] usbmount-864: Considering /dev/mmcblk0p1...
[ 9.877] usbmount-864: /dev/mmcblk0p1 is a valid block device
[ 9.892] Starting system message bus: dbus.
[ 9.950] ID_FS_UUID=3535-3938
[ 9.950] ID_FS_UUID_ENC=3535-3938
[ 9.950] ID_FS_TYPE=vfat
[ 9.960] usbmount-864: Filesystem on /dev/mmcblk0p1
[ 10.003] usbmount-864: ID_FS_TYPE=vfat
[ 10.019] usbmount-864: device_size=62325760
[ 10.019] usbmount-864: fsck_timeout=84
[ 10.084] lttng-sessiond(923):close(3) returning EBADF
[ 10.144] Spawning a session daemon
[ 10.144] Session bs created.
[ 10.144] Traces will be written in /var/volatile/lttng/lttng-traces/bs-19700101-000010
[ 10.280] UST channel channel0 enabled for session bs
[ 10.292] UST channel channel_high_freq enabled for session bs
[ 10.327] UTC read from RTC: Fri Mar 8 16:25:56 2019
[ 10.355] Starting dhcpcd eth0
[ 10.554] net-configure (957): undefined instruction: pc=b6d3aa88
[ 10.554] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 10.568] net-configure: eth0 start
[ 10.641] Successfully initialized wpa_supplicant
[ 10.721] f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, patch: 1
[ 10.724] f0b00000.ethernet: configuring instance for internal PHY
[ 10.724] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.764] EAP-PEAP/MSCHAPv2: No identity configured
[ 10.769] SYSC_close: 1020 callbacks suppressed
[ 10.769] net-configure(962):close(20) returning EBADF
[ 10.786] dhcpcd[962]: dhcpcd not running
[ 10.792] Name servers string: xxx
[ 10.808] dhcpcd[964]: eth0: adding address fe80::92ac:3fff:fe0d:d6ef
[ 10.809] dhcpcd[964]: forked to background, child pid 966
[ 10.816] No inbound bandwidth shaping on eth0
[ 10.820] IP:eth0 NOCARRIER down
[ 10.892] net-configure (977): undefined instruction: pc=b6d68a88
[ 10.892] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 10.898] net-configure: eth0 update
[ 10.926] dhcpcd[966]: eth0: waiting for carrier
[ 10.928] Waiting for link on eth0
[ 11.286] fsck.fat 3.0.25 (2014-01-17)
[ 11.286] /dev/mmcblk0p1: 798 files, 5577/973584 clusters
[ 11.305] timely: /sbin/dosfsck exited with 0 after 1s
[ 11.306] usbmount-864: fsck.vfat /dev/mmcblk0p1 succeeded
[ 11.315] usbmount-864: Successfully mounted /dev/mmcblk0p1 at /storage/sd.fwup
[ 11.317] usbmount-864: Cleaned up fsck cruft at /storage/sd.fwup
[ 11.353] save-crash-dump (995): undefined instruction: pc=b6cfba88
[ 11.353] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 11.383]
[ 11.383] Crash dump copied to: /storage/sd.fwup/brightsign-dumps/000021.dump
[ 11.385] usbmount-864: Looking for firmware update at /storage/sd.fwup
[ 11.419] No appropriate upgrade files found.
[ 11.420] usbmount-864: Migrating mounted filesystem from /storage/sd.fwup to /storage/sd
[ 11.928] Waiting for link on eth0
[ 12.721] libphy: f0b00000.etherne:01 - Link is Down
[ 12.928] Waiting for link on eth0
[ 13.928] Waiting for link on eth0
[ 14.757] libphy: f0b00000.etherne:01 - Link is Up - 1000/Full
[ 14.757] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 14.757] dhcpcd[966]: eth0: carrier acquired
[ 14.774] net-configure (1006): undefined instruction: pc=b6d87a88
[ 14.774] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 14.778] net-configure: eth0 update
[ 14.790] dhcpcd[966]: DUID 00:03:00:01:90:ac:3f:0d:d6:ef
[ 14.790] dhcpcd[966]: eth0: IAID 3f:0d:d6:ef
[ 14.790] dhcpcd[966]: eth0: probing address 10.xxxxx
[ 14.923] dhcpcd[966]: eth0: soliciting an IPv6 router
[ 14.928] Waiting for link on eth0
[ 14.929] Waiting for LLDP...
[ 16.931] Power source: PoE type 2 (25.0W)
[ 16.939] Not loading Broadcom WiFi driver because we are on POE power
[ 16.984] usbcore: registered new interface driver btusb
[ 17.030] USB vidpid=05e3:0610
[ 17.107] WiFi disabled because we are on POE power
[ 17.161] net.ipv4.conf.eth0.force_igmp_version = 0
[ 17.353] httpd (1112): undefined instruction: pc=b6d3aa88
[ 17.353] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 17.520] Panda firmware version 01.01 available for upgrades
[ 17.626] No Pandas found
[ 17.634] Starting extensions message bus: dbus.
[ 17.644] Skipping non-extension UBI writable
[ 17.645] Skipping non-extension UBI rootfs
[ 17.709] Feature 'EAC3' not set
[ 17.728] Feature 'AC3' not set
[ 17.769] share-terminal: serial console only
[ 17.831] bluetoothd[1183]: Bluetooth daemon 5.43
[ 17.835] bluetoothd[1183]: Starting SDP server
[ 17.842] bluetoothd[1183]: kernel lacks bnep-protocol support
[ 17.842] bluetoothd[1183]: System does not support network plugin
[ 17.847] bluetoothd[1183]: Failed to open RFKILL control device
[ 17.847] bluetoothd[1183]: Bluetooth management interface 1.10 initialized
[ 18.076] Starting BrightSign application...
[ 18.156] Starting brightsign tracing: default
[ 19.738] dhcpcd[966]: eth0: hardware address 50:61:bf:cf:fd:90 claims 10.xxx
[ 20.762] dhcpcd[966]: eth0: soliciting a DHCP lease
[ 24.175] brightsign (1237): undefined instruction: pc=b6c44a88
[ 24.175] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 24.300] dhcpcd[966]: eth0: offered 10.xxx from 10.xxx
[ 24.301] dhcpcd[966]: eth0: ignoring offer of 10.xxx from 10.xxx
[ 24.304] dhcpcd[966]: eth0: ignoring offer of 10.xxx from 10.xxx
[ 24.308] dhcpcd[966]: eth0: ignoring offer of 10.1xxx from 10.xxx
[ 24.324] dhcpcd[966]: eth0: probing address 10.xxx
[ 24.652] BrightSign application impala-7.0.60 starting
[ 24.693] NEXUS_BOX_MODE 10 videomode 4096x2160x60p parsed 1
[ 24.875] *** 00:00:00.153 nexus_platform_settings: MTG disabled
[ 24.896] Maximum audio sample rate supported: 192000Hz
[ 24.897] *** 00:00:00.001 nexus_platform_os: virtual l2 enabled
[ 24.897] *** 00:00:00.001 nexus_platform_os: shared gpio enabled
[ 24.898] *** 00:00:00.001 nexus_platform_cma: MEMC0 Placed HEAP[8] 32MBytes(0x2000000 Bytes) with alignment 0x100000 SAGE at 0x010000000 (256 MByte)
[ 24.898] *** 00:00:00.001 nexus_platform_cma: MEMC0 Placed HEAP[3] 112MBytes(0x7000000 Bytes) with alignment 0x100000 SAGE at 0x012000000 (288 MByte)
[ 24.898] *** 00:00:00.001 nexus_platform_cma: MEMC0 Placed HEAP[0] 128MBytes(0x8000000 Bytes) with alignment 0x100000 SAGE at 0x019000000 (400 MByte)
[ 24.898] *** 00:00:00.001 nexus_platform_cma: MEMC0 Placed HEAP[4] 348MBytes(0x15cd2000 Bytes) with alignment 0 at 0x021000000 (528 MByte)
[ 24.898] *** 00:00:00.001 nexus_platform_cma: MEMC1 Placed HEAP[9] 64MBytes(0x4000000 Bytes) with alignment 0 at 0x0a0000000 (2560 MByte)
[ 24.898] *** 00:00:00.001 nexus_platform_cma: MEMC1 Placed HEAP[5] 362MBytes(0x16afd000 Bytes) with alignment 0 at 0x0a4000000 (2624 MByte)
[ 24.898] *** 00:00:00.001 nexus_platform_cma: resetting all cma allocations in cma 0
[ 24.898] cma: cma_release(page cf3f9000)
[ 24.942] cma_driver: cma_dev_put_mem addr 0x60000000 len 0x20000000
[ 24.942] *** 00:00:00.046 nexus_platform_cma: cma:free PA 0x060000000, size 536870912 cma 0
[ 24.948] *** 00:00:00.051 BCHP_PWR:
[ 24.948] *** 00:00:00.052 BCHP_PWR: ****************************************
[ 24.948] *** 00:00:00.052 BCHP_PWR: ****************************************
[ 24.948] *** 00:00:00.052 BCHP_PWR: ** BCHP_PWR POWER MANAGEMENT DISABLED **
[ 24.948] *** 00:00:00.052 BCHP_PWR: ****************************************
[ 24.948] *** 00:00:00.052 BCHP_PWR: ****************************************
[ 24.948] *** 00:00:00.052 BCHP_PWR:
[ 25.120] *** 00:00:00.224 nexus_platform: impala B0 16.4, boxmode 10, product 72521 B2
[ 25.136] *** 00:00:00.239 BHSM: BSP Platform[4.2.0] BSECK[4.1.5] verified[yes] modes[0x0F] BFW Epoch[4]
[ 26.473] *** 00:00:01.576 nexus_statistics_module: sage[High] modules/sage/src/nexus_sage_svp.c:529 1264538 usec
[ 26.475] *** 00:00:01.578 bdsp_raaga_img: DDP decoding is not supported
[ 26.626] *** 00:00:01.729 BXVD: BXVD_Open() - Hardware revision: R, Firmware revision: 190421
[ 26.644] !!!Error BERR_INVALID_PARAMETER(0x2) at magnum/basemodules/dsp/src/raaga/firmware/fp2011/bdsp_raaga_img.c:1426
[ 26.644] ### 00:00:01.747 bdsp_raaga_fw_algo: Error in Opening the Image Interface for FW_ID =24
[ 26.644] !!!Error BERR_INVALID_PARAMETER(0x2) at magnum/basemodules/dsp/src/raaga/bdsp_raaga_fw_algo.c:5861
[ 26.644] !!!Error BERR_INVALID_PARAMETER(0x2) at magnum/basemodules/dsp/src/raaga/firmware/fp2011/bdsp_raaga_img.c:1426
[ 26.644] ### 00:00:01.747 bdsp_raaga_fw_algo: Error in Opening the Image Interface for FW_ID =25
[ 26.644] !!!Error BERR_INVALID_PARAMETER(0x2) at magnum/basemodules/dsp/src/raaga/bdsp_raaga_fw_algo.c:5861
[ 26.644] !!!Error BERR_INVALID_PARAMETER(0x2) at magnum/basemodules/dsp/src/raaga/firmware/fp2011/bdsp_raaga_img.c:1426
[ 26.644] ### 00:00:01.747 bdsp_raaga_fw_algo: Error in Opening the Image Interface for FW_ID =26
[ 26.644] !!!Error BERR_INVALID_PARAMETER(0x2) at magnum/basemodules/dsp/src/raaga/bdsp_raaga_fw_algo.c:5861
[ 26.690] *** 00:00:01.793 BXVD: BXVD_Open() - Hardware revision: R, Firmware revision: 190421
[ 26.713] *** 00:00:01.816 BVCE: FW v4.15.0.0 (0x040f0000) [API v5.15.0.0 (0x050f0000)][0]
[ 26.714] !!!Error BERR_INVALID_PARAMETER(0x2) at magnum/basemodules/int/bint.c:891
[ 26.714] !!!Error BERR_INVALID_PARAMETER(0x2) at magnum/portinginterface/i2c/src/bi2c.c:2673
[ 26.714] ### 00:00:01.817 nexus_i2c: Unable to open I2C Device Channel
[ 26.714] !!!Error BERR_INVALID_PARAMETER(0x2) at nexus/modules/i2c/src/nexus_i2c.c:214
[ 26.714] !!!Error BERR_INVALID_PARAMETER(0x2) at nexus/modules/i2c/src/nexus_i2c.c:322
[ 26.786] *** 00:00:01.889 nexus_platform: initialized
[ 26.786] *** 00:00:01.889 nexus_statistics_module: platform[High] nexus/base/src/nexus_base_scheduler.c:838 1388045 usec
[ 26.786] *** 00:00:01.889 nexus_statistics_callback: Timer callback 0x9352a8:0xb61f41b9 from common/src/linuxuser/nexus_platform_os.c:702 1388126 usec
[ 26.786] ### 00:00:01.889 nexus_timebase: NEXUS_Timebase_P_SetSettings: Unknown sample rate 0, assuming 48000
[ 26.786]
[ 26.840] *** 00:00:01.943 drm_common: DRM_Common_BasicInitialize - ******* Initializing Common DRM core (CMNDRM 1.27) *******
[ 26.843] NetworkTime: server changed to 'http://time.brightsignnetwork.com'
[ 26.843] NetworkTime: Configuration changed.
[ 26.880] commandline read: brightsign
[ 26.880]
[ 26.880] ~~~~~~~~~~~~~~~~~~~~~~~~~~| DirectFB 1.4.17 |~~~~~~~~~~~~~~~~~~~~~~~~~~
[ 26.880] (c) 2001-2012 The world wide DirectFB Open Source Community
[ 26.880] (c) 2000-2004 Convergence (integrated media) GmbH
[ 26.880] ----------------------------------------------------------------
[ 26.880]
[ 26.899] (*) DirectFB/Core: Single Application Core. (2017-12-27 13:41) [ DEBUG ]
[ 26.926] (*) Direct/Memcpy: Using libc memcpy()
[ 26.928] *** 00:00:00.000 platform_init: Broadcom Corporation DirectFB Platform Layer Version 7.0
[ 26.928] *** 00:00:00.000 nexus_common_init: Display heap: handle=0x93f5e8 size 524288kB - free 524284kB - largest block 524284kB
[ 26.928] *** 00:00:00.000 nexus_common_init: Offscreen heap: handle=0x93f5e8 size 524288kB - free 524284kB - largest block 524284kB
[ 26.971] (*) DirectFB/Graphics: Broadcom Corporation Bcmnexus Packet Buffer GFX Driver 4.3 (Broadcom Corporation)
[ 27.060] (*) Direct/Thread: Started 'BRCM NotifyDisplay' (-1) [OUTPUT OTHER/OTHER 0/0] <1048576>...
[ 27.067] (*) DirectFB/Core/WM: Default 0.3 (directfb.org)
[ 27.184] *** 00:00:00.256 BHDM_EDID: UHD resolution, but using BT.709
[ 27.364] *** 00:00:00.436 nexus_statistics_module: display[High] nexus/base/src/nexus_base_scheduler.c:949 118380 usec
[ 27.364] *** 00:00:00.436 nexus_statistics_callback: Event callback 0x9c4138:0xb62c89a1 from modules/display/src/nexus_display.c:991 118435 usec
[ 27.364] *** 00:00:00.436 nexus_statistics_api: NEXUS_Display_AddOutput[display:High] 181694 usec
[ 27.365] *** 00:00:00.437 platform_nexus_display: HDMI hotplug event: connected
[ 27.365] *** 00:00:00.437 BHDM_EDID: UHD resolution, but using BT.709
[ 27.566] *** 00:00:00.638 nexus_statistics_callback: TaskCallback callback 0x9b4e58:0xb61feead from modules/hdmi_output/src/nexus_hdmi_output.c:456 200972 usec
[ 27.566] *** 00:00:00.638 nexus_statistics_module: hdmi_output[Low] nexus/core/syncthunk/nexus_hdmi_output_thunks.c:26 200842 usec
[ 27.566] *** 00:00:00.638 nexus_statistics_api: NEXUS_HdmiOutput_GetVendorSpecificInfoFrame[hdmi_output:Low] 200889 usec
[ 27.586] *** 00:00:00.658 BHDM_EDID: UHD resolution, but using BT.709
[ 27.787] *** 00:00:00.859 nexus_statistics_callback: TaskCallback callback 0x9b4e58:0xb61feead from modules/hdmi_output/src/nexus_hdmi_output.c:456 200854 usec
[ 27.787] *** 00:00:00.859 nexus_statistics_module: hdmi_output[Low] nexus/core/syncthunk/nexus_hdmi_output_thunks.c:26 200755 usec
[ 27.787] *** 00:00:00.859 nexus_statistics_api: NEXUS_HdmiOutput_GetVendorSpecificInfoFrame[hdmi_output:Low] 200778 usec
[ 28.465] dhcpcd[966]: eth0: no IPv6 Routers available
[ 29.198] Using /storage/sys/default-4k-edid.bin EDID
[ 29.203] *** 00:00:02.275 BHDR_HDCP_PRIV: HDCP Key Set invalid/not loaded to RAM
[ 29.203] *** 00:00:02.275 BHDR_HDCP_PRIV: HDCP BKsv Valid: 0
[ 29.203] *** 00:00:02.275 BHDR_HDCP_PRIV: HDCP Keys loaded to RAM: 0
[ 29.287] HDCP2.2 TX key read successfully
[ 29.287] HDCP2.2 RX key read successfully
[ 29.287] *** 00:00:02.359 BHDM_EDID: UHD resolution, but using BT.709
[ 29.411] dhcpcd[966]: eth0: using static address 10.xxx
[ 29.412] dhcpcd[966]: eth0: adding route to 10.xxx
[ 29.412] dhcpcd[966]: eth0: adding default route via 10.xxx
[ 29.415] IP:eth0 STATIC ip=10.xxx nm=255. gw=10.xxx domain=.com dns=3 3
[ 29.447] net-configure (1284): undefined instruction: pc=b6d1ba88
[ 29.447] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 29.462] net-configure: eth0 update
[ 29.488] *** 00:00:02.560 nexus_statistics_callback: TaskCallback callback 0x9b4e58:0xb61feead from modules/hdmi_output/src/nexus_hdmi_output.c:456 201265 usec
[ 29.488] *** 00:00:02.560 nexus_statistics_module: hdmi_output[Low] nexus/core/syncthunk/nexus_hdmi_output_thunks.c:26 185090 usec
[ 29.488] *** 00:00:02.560 nexus_statistics_api: NEXUS_HdmiOutput_GetAudioConnector[hdmi_output:Low] 185148 usec
[ 29.512] save-crash-dump (1290): undefined instruction: pc=b6dc5a88
[ 29.512] Code: e320f000 e320f000 f2200150 e12fff1e (ec510f1e)
[ 29.588] bs_native_window_clip_dimensions:751 stretch 0 position 0,0 4096x2160 nw 2048x1080 clip 2048x1080 format 2048x1080
[ 29.816] This plugin does not support createPlatformOpenGLContext!
[ 30.717] Loading 'SD:/autorun.brs' (50da0a5ad390e67c3190b3aa0177cbf85b849c3d)
[ 31.589] Setting system clock to 1552062377.000000
[ 31.589] NetworkTime: clock set to 2019/03/08 16:26:17.000 UTC
[ 31.646] Analog output 1 unsupported on this hardware
[ 31.646] Analog output 2 unsupported on this hardware
[ 31.650] Analog output 1 unsupported on this hardware
[ 31.650] Analog output 2 unsupported on this hardware
[ 31.666] !!!Error BERR_NOT_SUPPORTED(0x8) at nexus/modules/file/src/linuxuser/nexus_file_posix.c:177
[ 31.666] TIME: Probe = 0.015679
[ 31.668] ### 00:00:04.478 bape_equalizer: No valid SRC handle in EQ handle 0xe5b390
[ 31.669] TIME: ConfigureResources = 0.018621
[ 31.698] ### 00:00:04.508 nexus_audio_decoder: Decoder not started or suspended
[ 31.699] ### 00:00:04.509 nexus_audio_decoder: Decoder not started or suspended
[ 31.701] Set output 2 timebase to HDMI AUDIO IN
[ 31.702] *** 00:00:04.512 BHDM_PACKET_ACR_PRIV_ISR: Audio Sample Rate Change from 2 to 1
[ 31.713] *** 00:00:04.523 BVDC_HDDVI: HdDvi[0] bSwReset
[ 31.801] Both HDMI timebases are locked. OK to run audio from MAI clock.
[ 32.046] *** 00:00:04.856 BVDC_PRIV: (D) Display[0] acquires control of source[17]'s slots
[ 32.080] *** 00:00:04.889 nexus_statistics_module: display[High] nexus/base/src/nexus_base_scheduler.c:949 366468 usec
[ 32.080] *** 00:00:04.890 nexus_statistics_callback: Event callback 0xd18800:0xb62d6ad5 from modules/display/src/nexus_video_input.c:255 366549 usec
[ 32.080] *** 00:00:04.890 nexus_statistics_api: NEXUS_VideoWindow_AddInput[display:High] 367166 usec
[ 32.080] ### 00:00:04.890 bape_input_port: Node InputCapture 0 can not accept this InputPort's data format (Unknown)
[ 32.080] ### 00:00:04.890 nexus_timebase: NEXUS_Timebase_P_SetSettings: Unknown sample rate 0, assuming 48000
[ 32.080]
[ 32.090] Playing video to video layer
[ 32.090] FireEvent 27 MEDIAPREPARED (line 1660)
[ 32.164] Set output 2 timebase to HDMI AUDIO IN
[ 32.164] FireEvent 3 PLAYING (line 1693)
[ 32.164] TIME: PlayVideoInput = 0.465863
[ 32.178] dhcpcd[966]: eth0: hardware address 00:7e:95:22:55:b2 claims 10.xxx
[ 32.264] Both HDMI timebases are locked. OK to run audio from MAI clock.
[ 32.293] dhcpcd[966]: eth0: hardware address 50:61:bf:f9:7c:31 claims 10.xxx
[ 32.296] dhcpcd[966]: eth0: hardware address 50:61:bf:f9:7c:b2 claims 10.xxx
[ 32.300] dhcpcd[966]: eth0: hardware address 00:7e:95:10:6a:b2 claims 10.xxx
[ 32.301] dhcpcd[966]: eth0: hardware address 84:8a:8d:60:c9:b2 claims 10.xxx
[ 33.090] HDMI capture in error (0 0 1 0)
[ 34.090] HDMI capture in error (0 0 1 0)
[ 35.091] HDMI capture in error (0 0 1 0)
[ 36.091] HDMI capture in error (0 0 1 0)
[ 36.200] *** 00:00:09.010 bape_input_capture: Input Capture 0 already stopped
[ 36.279] Set output 2 timebase to FREERUN
[ 36.476] *** 00:00:09.286 BHDM_PACKET_ACR_PRIV_ISR: Audio Sample Rate Change from 1 to 2
[ 36.522] Analog output 1 unsupported on this hardware
[ 36.522] Analog output 2 unsupported on this hardware
[ 36.525] Analog output 1 unsupported on this hardware
[ 36.525] Analog output 2 unsupported on this hardware
[ 36.525] !!!Error BERR_NOT_SUPPORTED(0x8) at nexus/modules/file/src/linuxuser/nexus_file_posix.c:177
[ 36.525] TIME: Probe = 0.000064
[ 36.525] TIME: ConfigureResources = 0.000342
[ 36.547] ### 00:00:09.357 nexus_audio_decoder: Decoder not started or suspended
[ 36.547] ### 00:00:09.357 nexus_audio_decoder: Decoder not started or suspended
[ 36.896] *** 00:00:09.706 BVDC_PRIV: (D) Display[0] acquires control of source[17]'s slots
[ 36.929] *** 00:00:09.739 nexus_statistics_module: display[High] nexus/base/src/nexus_base_scheduler.c:949 366492 usec
[ 36.929] *** 00:00:09.739 nexus_statistics_callback: Event callback 0xacaa90:0xb62d6ad5 from modules/display/src/nexus_video_input.c:255 366541 usec
[ 36.929] *** 00:00:09.739 nexus_statistics_api: NEXUS_VideoWindow_AddInput[display:High] 366877 usec
[ 36.930] ### 00:00:09.739 bape_input_port: Node InputCapture 0 can not accept this InputPort's data format (Unknown)
[ 36.930] ### 00:00:09.740 bape_input_port: Node InputCapture 1 can not accept this InputPort's data format (Unknown)
[ 36.930] ### 00:00:09.740 bape_input_port: Node InputCapture 2 can not accept this InputPort's data format (Unknown)
[ 36.930] ### 00:00:09.740 nexus_timebase: NEXUS_Timebase_P_SetSettings: Unknown sample rate 0, assuming 48000
[ 36.930]
[ 36.940] Playing video to video layer
[ 36.940] FireEvent 27 MEDIAPREPARED (line 1660)
[ 37.013] FireEvent 3 PLAYING (line 1693)
[ 37.013] TIME: PlayVideoInput = 0.466127
[ 37.940] HDMI capture in error (0 0 1 0)
[ 38.940] HDMI capture in error (0 0 1 0)
[ 39.940] HDMI capture in error (0 0 1 0)
[ 40.940] HDMI capture in error (0 0 1 0)
[ 41.941] HDMI capture in error (0 0 1 0)
[ 41.941] !!!! Video freeze, ''
[ 41.941] FireEvent 8 MEDIAENDED (line 3123)
[ 60.744] dhcpcd[966]: eth0: hardware address 00:7e:95:25:b7:b2 claims 10.xxx
[ 91.204] *** 00:01:04.014 BHDR: Audio Sample Rate Change Detected f
[ 91.204] *** 00:01:04.014 BHDR: CH0 Error getting Channel Status bits for 0Hz (no Update) - uiChannelStatusBits 0f
[ 91.205] *** 00:01:04.015 bape_mai_input: No clock source found downstream. Find availble NCO otherwise, default to NCO0 . This may indidate a problem.
[ 91.205] *** 00:01:04.015 bape_input_capture: Input Capture 2 already stopped
[ 91.206] *** 00:01:04.016 bape_mai_input: No clock source found downstream. Find availble NCO otherwise, default to NCO0 . This may indidate a problem.
[ 91.206] *** 00:01:04.016 bape_input_capture: Input Capture 1 already stopped
[ 91.206] *** 00:01:04.016 bape_mai_input: Currently MAI IN requires a downstream output that uses an NCO (typically MAI output or Dummy output
[ 91.206] *** 00:01:04.016 bape_input_capture: Input Capture 0 already stopped
[ 91.206] ### 00:01:04.016 bape_resources: Insufficient buffers available to support output format IEC-61937 Compressed. Buffers can be increased in BAPE_Settings.
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_resources.c:202
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_resources.c:135
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_mixer_standard.c:2585
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_mixer_standard.c:1080
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_path_priv.c:131
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_input_capture.c:461
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at nexus/modules/audio/src/ape_raaga/nexus_audio_input_capture.c:836
[ 91.206] *** 00:01:04.016 bape_input_capture: Input Capture 0 already stopped
[ 91.206] ### 00:01:04.016 bape_resources: Insufficient buffers available to support output format IEC-61937 Compressed. Buffers can be increased in BAPE_Settings.
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_resources.c:202
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_resources.c:135
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_mixer_standard.c:2585
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_mixer_standard.c:1080
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_path_priv.c:131
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at magnum/portinginterface/ape/src/raaga/bape_input_capture.c:461
[ 91.206] !!!Error BERR_OUT_OF_DEVICE_MEMORY(0x4) at nexus/modules/audio/src/ape_raaga/nexus_audio_input_capture.c:836
[ 91.262] *** 00:01:04.072 BVDC_HDDVI: HdDvi[0] bSwReset
[ 91.304] *** 00:01:04.114 BHDR: CH0 ***HDMI MODE***
[ 91.396] *** 00:01:04.206 BVDC_DBG: BVNE eHscl_1_STATUS 0x10 Addr 0x69048c [ts=11733449] 1 total
[ 91.429] *** 00:01:04.239 BVDC_DBG: BVNE eMcdi_1_STATUS 0x80 Addr 0x692028 [ts=11766757] 1 total
[ 91.429] *** 00:01:04.239 BVDC_DBG: BVNE eMvp_1_STATUS 0x2 Addr 0x690024 [ts=11766780] 1 total
[ 91.429] *** 00:01:04.239 BVDC_DBG: BVNE eScl_1_STATUS 0x180 Addr 0x6204b0 [ts=11766799] 1 total
[ 91.874] *** 00:01:04.684 BVDC_SRC: (S) Source[17] enters Xfer state
[ 91.908] *** 00:01:04.718 BVDC_SRC: (S) Source[17] re-acquires control of its slots
